1.
Some suggestions of cantilever installation of steel box shaped girder are given.
对悬拼法钢箱梁安装提出了一些有益的建议。
2.
Research on Mechanical Performance of 300 Metres Span RC Arch Bridge with Cableway and Cantilever Erection;
300米跨缆吊悬拼施工RC箱型拱桥受力性能研究
3.
Research on Construction Controlling of Reinforced Concrete Arch Bridge with Precast Segmental Cantilever;
悬拼钢筋混凝土箱型拱桥施工控制的研究
4.
Long-span prestressed box girder precasting,cantilever assembly construction and quota analysis thereof;
大跨度预应力箱梁预制悬拼施工及定额分析
5.
The Design of a Crane for Bridge Suspending and Combining in the Construction of Exceeding High Cloverleaf Junction
超高立交桥施工用悬拼架桥起重机的设计
6.
Analysis of Mechanical Behavior in Construction of Oblique-pulling Truss Bridge
斜拉桁架桥悬拼施工过程的力学行为分析
7.
Analysis of Section Transverse Deformation of Flat Steel Box Girder of Cable-stayed Bridge during Cantilevered Assembling Based on Finite Element Method
斜拉桥扁平钢箱梁悬拼阶段截面对接变形有限元分析
8.
Study on Construction Control of Cantilever Erection Continuous Curved Girder Bridge;
悬臂拼装曲线连续梁桥施工控制研究
9.
Study on Construction Technology of Box Girder Segment s Stub Matching Precast and Cantilever Erection;
箱梁短线匹配预制及悬臂拼装施工技术研究
10.
Study on Construction Geometry Control of Prefabrication Based on Short-Line Method and Cantilever Erection Continuous Girder Bridge;
短线预制悬臂拼装连续梁桥施工线形控制研究
11.
Comprehensive Application of Construction Techniques for Segmental Precasting and Cantilever Assembling to Bridge Works
节段预制、悬臂拼装工艺在工程中的综合运用
12.
FINITE ELEMENT ANALYSIS OF BEAM-TO-COLUMN CONNECTION WITH CANTILEVER BEAM BOLTED-SPLICING
带悬臂梁段拼接的梁柱连接有限元分析
13.
Research on Method of Geometry Control during Cantilever Erection of PC Cable-Stayed Bridges;
预应力混凝土斜拉桥悬臂拼装施工线型控制方法研究
14.
Monitoring of Construction and Test under Vehicle Load for Large Boxed Girder with Cantilever Assembled Spines;
大型悬臂拼装脊骨箱梁桥施工监测与车载试验研究
15.
Research and Application of Cantilever Assembly Equipment to Prefabricated Segmental Box Girder of Shanghai Yangtze River Tunnel-Bridge Section B6
上海长江隧桥B6标预制节段箱梁悬臂拼装设备研究与应用
16.
Study on Construction Technology for Pre-fabricated Segmental Box Girder Cantilever Erection in Shanghai Yangtze River Tunnel-Bridge Section B6
上海长江隧桥B6标预制节段箱梁悬臂拼装施工技术研究
17.
A case study for Nanning Bridge, the first long span unsymmetrical extroversion arch bridge with curve beam in the world is given.
利用几何方法推导了空间钢箱拱肋节段拼装误差在拱肋最大悬臂端的累积规律。
18.
Collapse Mechanism and Design Criterion of Steel Beam-to-Column Connection with Cantilever Beam Splicing under Cyclic Load;
带悬臂梁段拼接的梁柱连接在循环荷载作用下的破坏机理及抗震设计对策