1.
The Influence of the Numbers of Movable and Stationary Flat on Nep and Impurity
活动盖板和固定盖板根数对棉结杂质的影响
2.
Very close setting of front plate or non-parallel setting.
前固定盖板针布隔距太紧或与锡林针布不平行。
3.
We have acomplished some experimental study on the mixing action in carding machine, employing different lengths of cotton fiber, increasing the number of fixed flats and decreasing the number of moving flats.
就棉纤维长度、增加固定盖板根数、减少活动盖板根数对混合作用的影响做了试验研究。
4.
The effect of card back fixed flat setting on the removal of immature fibers
梳棉机后固定盖板隔距对未成熟纤维去除的影响
5.
Study on the Back Stationary Flat and Webclean in Carding Machine;
梳棉机加装后固定盖板及棉网清洁器问题的研究
6.
Effect of back stationary flat number of carding machine on removal of immature fiber
梳棉机后固定盖板根数对未成熟纤维去除的影响
7.
Cylinder has cover board and web cleaner fixed in front and at back. Takerin dehairing board adopts aluminium section structure. Accessories are light and handy and dust-absorbing effect is good.
锡林前后固定盖板及棉网清洁器，刺辊分梳板等采用铝型材结构，零件轻巧，吸尘杂效果好。
8.
crowfoot holddown
将盖子固定在搭板上的叉子
9.
deck securing fitting
甲板绑扎固定用具; 甲板或舱盖上固定集装箱的装置
10.
Remove the four screws that secure the ACM mounting bracket to the floor pan transmission tunnel.
拆去固定ACM固定支架到底板变速器-传动轴盖板的四个螺丝。
11.
Position the underhood lamp on the hood inner panel.
将引擎盖未闭合灯固定于引擎罩内板上。
12.
Install push-in fasteners holding trunk lid slam bumpers to top of fascia.
安装将行李厢盖沿保险杆紧固到面板顶部上的推进式固定件。
13.
Remove push-in fastener attaching trim cover to door inner panel (use special tool C-4829).
拆下把装饰盖板固定在车门内板的压入式钩扣（用特殊工具C-4829）。
14.
Be sure the dummy club of the bar put into the restrict slot followed by tightening the fastening screws of cover plate
一定要将芯棒的凸台装入限位槽内，拧紧盖板紧固螺丝。
15.
a narrow strip of wood used to fasten down the edges of the material that covers hatches in foul weather.
压板条:一种用来固定在恶劣天气下遮盖船舱口材料边缘的窄木条。
16.
"Drill & tap for M16X2-1.38 Deep NPT,16 places for cover plate mounting screw"
钻孔,攻出一只M16X2-1.38深NPT螺纹,16处,该螺纹应与盖板固定螺丝配套
17.
The fiats are attached to a steel cylinder or to an endless belt that rotates over the top portion of the cylinder.
有的盖板则固定在锡林上；有的被固定在一个环状的带子上,带子沿锡林上方回转。
18.
Screw, crank cover
曲柄轴盖子固定螺丝