1.
Finite Element Simulation of Continuous Casting Square Slab and Selecting of Induction Heating Parameters during Hot Dilivery and Direct Rolling;
连铸方坯热送直轧过程的有限元模拟及感应补热参数选择
2.
The Simulation of Temperature for Continuously Casting Slabs during Hot Steel Rolling and Designed of the Industry Software;
连铸方坯热送直轧温度场的计算机仿真及工业软件开发
3.
ON TECHNICAL AND ECONOMICAL BENEFIT OF HOT CONVEYANCE AND HOT CHARGE AND DIRECT ROLLING OF CONTINUOUS CAST BLANK
连铸坯热送热装和直接轧制的技术经济效益
4.
The Hot Delivery and Hot Charging at Masteel's 2250mm Hot Rolling Mill
马钢2250mm热轧热送热装生产模式研究
5.
Study on Temperature Field of the Transfer Roller in Hot Strip Mill by FEA;
热连轧输送辊道温度场的有限元分析
6.
The cold rolled coils are delivered from cold rolling mill into the hot dip galvanizing workshop. The coils leave hot dip galvanizing workshop in form of galvanized coils as final product.
冷轧卷从冷轧车间送至热镀锌车间,成品镀锌卷离开热镀锌车间。
7.
Analysis on Fragmentation of 34CrMo4 Hot Rolled Seamless Steel Tube When Straightening
34CrMo4热轧无缝钢管矫直碎裂分析
8.
Hot-rolled wide strips for line pipe of oil and natural gas
GB/T14164-1993石油天然气输送管用热轧宽钢带
9.
Analyzing and Improvement on the Sealing Invalidation of the Pinch Roller in Continuous Hot rolling Caster
热轧连铸机夹送辊密封失效原因分析及改进
10.
Application of Hot Delivery and Hot Charging of Continuous Casting Blank Rolling Technology in Chongqing Iron and Steel Co.,Ltd.
连铸坯热送热装轧制技术在重钢高线厂生产中的应用
11.
Causes Analysis of Surface Cracking on Ti-microalloyed Steel Slab during Rough Rolling
热送热装Ti微合金化连铸钢坯粗轧表面裂纹成因分析
12.
Signal Test and Analysis of Hydraulic System of Straightening Machine in a Hot Rolling Plant of Wuhan Iron and Steel
武钢热轧厂矫直机液压系统信号测试与分析
13.
Research on Residual Stress Distribution of High Strength Hot-rolled Plate before and after Straightening
热轧高强度钢板矫直前后残余应力分布的研究
14.
Design and research on high speed straightening system of hot rolled ribbed bar
热轧带肋钢筋高速矫直系统设计与研究
15.
tongue-and-groove pass
闭口[直轧闭]孔型
16.
Application of the Collet Connection Technology for Pell off The Ribs and Rolling Plain Bar in Hot-Rolled Swirl Pool Project of Masteel 2250mm Hot Strip Mill While Against Construction;
钢筋剥肋滚轧直螺纹套筒连接技术在马钢新区热轧旋流池逆作施工中的应用
17.
according to the temperature of the metal being rolled, rolling processes can be classified as hot rolling and cold rolling. and the rolled products can thus be specified as hot rolled or cold rolled products.
根据轧制轧材的温度，轧制可分为热轧和冷轧;因而轧制产品也可分为热轧产品和冷轧产品。
18.
Wire: usually produced from hot-roiled rod by drawing; smaller than 4mm in diameter usually with a round section.
线材--一般用热轧细棒材拔拉而成，:直径小于4mm，横断面一般为圆形。