1.
Investigation on the Size Distribution and Microstructure of Sprayed Powder of GCr15 by Spray Forming
喷射成形GCr15钢过喷粉末尺寸分布及组织特征的实验研究
2.
Determination of crystallite size and strain by X-ray powder
晶粒尺寸和应变的X射线粉末衍射法测定
3.
The molybdenum alloy reinforced by lanthana particles with the sizes of nanometer and micron was prepared by powder metallurgy.
采用粉末冶金法制备了微米尺寸和准纳米尺寸的氧化镧粒子增强钼合金。
4.
" Powder metallurgy plain bearing--Cylindrical type--Types, dimensions and tolerances"
GB/T2685-1981滑动轴承粉末冶金筒形轴承型式、尺寸与公差
5.
" Powder metallurgy plain bearing--Rimed cylindrical type--Types, dimensions and tolerances"
GB/T2686-1981滑动轴承粉末冶金带挡边筒形轴承型式、尺寸与公差
6.
" Powder metallurgy plain bearing--Spherical type--Types, dimensions and tolerances"
GB/T2687-1981滑动轴承粉末冶金球形轴承型式、尺寸与公差
7.
Process and Dimensional Precision Research on Powder Injection Molding of Ti(C, N) Based Cermets;
Ti（C，N）基金属陶瓷粉末注射成形工艺和尺寸精度研究
8.
Study on Toner Mean Particles Size by Image Analysis Technology
图像分析法测试墨粉颗粒尺寸的初步研究
9.
The Study on the Optimization of Hamer Demenions and Arrangement of SWFP66X60A Hamer Mill
SWFP66X60A型锤式粉碎机锤片尺寸及排列方式优化研究
10.
The measurement of ironstone particulates based on computer vision
基于计算机视觉的铁矿石粉微粒尺寸的检测
11.
AN APPROACH TO MAGNETIC PARTICLE DETECTION TECHNOLOGY USED FOR ANGLE WELD JOINT ON SMALL SIZE TUBE SOCKET BASED ON YOKE MAGNETIZATION METHOD
小尺寸管座角焊缝磁轭法磁粉检测工艺探讨
12.
full size drawing
原尺寸图，实物尺寸图
13.
foot in the door technique
得寸进尺法得寸进尺法
14.
The measurements are 108 by 48 by 3 inches.
尺寸是高108英寸，宽48英寸，厚3英寸。
15.
The effect of particle size on phase transformation behaviors of Mg-3Ni-2MnO_2 hydrogen storage materials during dehydrogenation process
颗粒尺寸对Mg-3Ni-2MnO_2储氢复合粉体放氢过程相转变行为影响
16.
Gray Correlation Analysis on the Properties of Cement Mortar with the Particle Size Distribution of Clinker and Fly Ash
熟料和粉煤灰的颗粒尺寸分布与水泥性能的灰色关联分析
17.
Crystallite Size and Lattice Distortion of TiC from X-ray Diffraction Line Profile Analysis
用XRD线形分析法表征TiC粉体中的镶嵌尺寸与晶格畸变
18.
A size of paper, usually18?3 inches or17阶22 inches.
中号尺寸纸张的尺寸，通常为18223英寸或17222英寸