1.
Failure Pressure Analysis of SG Tube with Axial Crack
蒸汽发生器含轴向裂纹传热管的失效压力分析
2.
Numerical Simulation of Temperature Field and Stress Field for and Axial Crack Analysis of Heavy-wall Centrifugally Cast Hollow Bloom
厚壁离心管坯温度场和热应力场的数值模拟及其轴向裂纹分析
3.
Analysis of Fundamental Frequencies of Rotating Shafts with Transverse Crack;
含横向裂纹的转动轴的振动基频分析
4.
Analysis on Performance of Axial Throughwall Crack Pipeline Repaired by Sleeve
轴向穿透裂纹管道套管修复性能研究
5.
Analysis on the vibration characteristics of cracked beams subjected to axial force
轴向压力影响下裂纹梁振动特性分析
6.
Elastic-Plastic Finite Element Analysis for Piping Elbow with Axial Inside Surface Cracks;
光滑弯管沿轴向内表面裂纹弹塑性有限元分析
7.
Influence of transverse crack model on shafting's torsional shear stress
轴系横向裂纹模型对其扭转剪应力的影响
8.
Elastic-Plastic Fracture Analysis for Internal Axial Surface Half Elliptical Cracks in Oil & Gas Pipeline
油气管道内部轴向表面半椭圆裂纹弹塑性断裂分析
9.
FRACTURE AND RELIABILITY ASSESSMENT ON SUBMARINE PIPELINES WITH AXIAL SURFACE CRACKS
带轴向表面裂纹海洋管道的断裂计算与可靠性评估
10.
To ensure this, specimens must be of sufficient thickness so that a triaxial state of stress can exist at the flaw tip.
为此，试样必须足够厚，使裂纹顶端处于三轴向的应力状态。
11.
Elastic-Plastic Finite Element Analysis for Unequal-Diameter Tee Joint with Axial Through-wall Cracks at the Shoulder
焊制异径三通肩部轴向穿透裂纹弹塑性有限元分析
12.
The Experimental Analysis of the Correction Factor of the SIF for the Transverse Surface Semi-Elliptic Crack of a Axle
轴表面横向半椭圆裂纹应力强度因子修正系数的实验分析
13.
SIMULATION AND EXPERIMENTAL INVESTIGATION ON COUPLED STIFFNESS OF ROTATING SHAFT WITH TRANSVERSE CRACK
具有横向裂纹转轴耦合刚度的数值模拟和实验研究
14.
Shaft crack fault diagnosis based on grid support vector machines
基于网格式支持向量机算法的转轴裂纹故障诊断
15.
Hardening Crack Analysis and Prevention Measurement for 45 SteelWobbling Arm Axis
45钢摆臂轴淬火裂纹分析及防止措施
16.
RESEARCH OF THE FATIGUE CRACK PROPAGATION CHARACTERISTIC ON RAILWAY HOLLOW AXLES
高速客车空心车轴裂纹扩展特性研究
17.
Simulation for Short Fatigue Cracks Initiation of LZ50 Axle Steel for Railway Vehicles
LZ50车轴钢疲劳短裂纹萌生的数值模拟
18.
(2) The method which used to build the unequal-diameter tee joint with axial through-wall crack has been established.
(2) 确定了肩部含轴向穿透裂纹焊制异径三通有限元模型的建立方法。