1.
Method of Decreasing the Synthesis Temperature for Strontium Aluminates Europium Dysprosium Phosphors;
铝酸锶铕镝发光材料的低温合成工艺研究
2.
Study on Technical Parameter and Formation Mechanism of Low Temperature-synthesized Coal Gangue Cement;
低温合成煤矸石水泥工艺参数及形成机理研究
3.
Research on Low Temperature Moulding Process of New Type Composite Friction Material
新型复合摩擦材料的低温成型工艺研究
4.
SYNTHESIS OF MgO NANOCRYSTALLINE POWDER BY LOW-TEMPERATURE COMBUSTION
低温燃烧法合成纳米MgO粉体工艺的研究
5.
A New Low-Temperature Synthesizing Process of Methanol from CO/CO_2/H_2 and Catalysts Used
CO/CO_2/H_2低温合成甲醇新工艺及催化剂研究
6.
Research on the Catalyst and Reaction Process for Methanol Synthesis at Low Temperature in Slurry Phase;
低温液相合成甲醇铜铬催化剂制备及合成工艺的研究
7.
Influence of Polymerization Technology and Monomer Ratio on the Minimum Film Forming Temperature of Vinyl Ace-tate/Styrene/Acrylic Emulsion/
聚合工艺和单体配比对醋苯丙乳液最低成膜温度的影响
8.
The Research of Chemical Co-precipitation Synthesis NiCuZn Ferrite and Low Temperature Sintering Process
化学共沉淀法合成NiCuZn铁氧体及低温烧结工艺研究
9.
Synthesis of(La_(0.8)Sr_(0.2))_(0.9)MnO_(3-δ) powder by a gel-casting technique as cathodes for solid oxide fuel cells
采用凝胶注模工艺低温合成锶掺杂的锰酸镧粉体
10.
Study on Synthetic Technique of Low Cost and Low Toxic Urea-formaldehyde Resins;
低成本环保脲醛树脂合成工艺的研究
11.
INVESTIGATION ON TECHNOLOGICAL CONDITION OF LOWERING FIRING TEMPERATURE OF QINZHOU NIXING POTTERY
降低钦州坭兴陶烧成温度的工艺条件研究
12.
The Study on the Integration Process of Rectisol Process and Withdrawal of Methane Process by Deep Refrigeration;
低温甲醇洗与深冷回收甲烷相结合工艺的研究
13.
Double-side,two-men vertical welding procedures for small-diameter cryogenic aluminum alloy pipelines
小直径低温铝合金管道双人双面立焊工艺
14.
Mechanism and Process of Cu-Sn Bonding for Wafer Level MEMS Packaging
MEMS圆片级封装用Cu-Sn低温键合机理与工艺研究
15.
Study on Low Temperature Glass Frit Bonding for MEMS Device
MEMS器件封装的低温玻璃浆料键合工艺研究
16.
The Study on AZ31 Magnesium Alloy Car Hub Warm Forming Technology;
AZ31镁合金轿车轮毂温成形工艺研究
17.
The Study on Titanium Alloy ZTC4 Impacting Sheet Warm Deformation Technology;
ZTC4钛合金冲击板温成形工艺研究
18.
A Study on Forming Processes of Conical Cups with TA2M Titanium Alloy Sheets
TA2钛合金锥形件室温成形工艺研究