1.
The investigation on a new kind of Mo-Cu alloy material for electronic sealing material
新型低膨胀Mo-Cu合金电子封接材料研究
2.
Research on Synthesizing and Performance of Sealant for Solid Oxide Fuel Cells;
固体氧化物燃料电池封接材料的合成与性能研究
3.
To match with the spinel, a low temperature frit glass and funnel glass with similar thermal expansion are developed.
分析了封接中材料匹配、浸润性以及再结晶等原理，叙述了封接工艺。
4.
joint gasket- or packing- type, of metal sheeting combined with other material (e.g. asbestos, felt, paperboard)
金属片与其他材料（例如,石棉、毡、纸板）的静密封或填密封式接合衬垫
5.
rubber packing materials for industrial use
工业用密封橡胶材料
6.
A material used to prevent leakage or seepage, as around a pipe joint.
密封圈用来防止漏水或渗漏的一种材料，如水管的接合处
7.
The preparation and properties of superfine glass powder/epoxy resin composites were studied.
研究了玻璃粉／环氧树脂封接复合材料的制备与性能。
8.
Spinel exhibits a lower thermal expansion coefficient than conventional glass faceplate.
给出了封接结构、所用屏、低熔点玻璃和锥的材料特性。
9.
Design and Fabrication of Functionally Graded Material for Sealing High-pressure Gas Discharge Lamps;
高强气体放电灯管封接用功能梯度材料的设计与制备
10.
Effect of Grafted Particles PGMA/Al_2O_3 on Toughness and Reinforce of Encapsulating Materials of Epoxy Resin
接枝微粒PGMA/Al_2O_3对环氧树脂电子灌封材料的增强增韧作用
11.
Any material deviations from standard - packing, gasket, Bolting, etc.
任何与标准配置不同的材料:密封材料,沉淀材料,螺栓材料,等等。
12.
Research of Sealing and Heat-insulating Coating on Composite Case External Surface
复合材料壳体外表面密封、隔热涂层材料的研究
13.
Research Progress of Diamond-Cu Composite Material for Electronic Packaging
电子封装材料用金刚石/铜复合材料的研究进展
14.
sealing compound
电缆膏； 封口膏， 密封剂， 油灰， 腻子； 电瓶封口填料； 密封接合物
15.
Development of Removal Free Protection Film for Internal Wall of Artillery Tube
火炮身管内壁免启封润滑封存膜材料的研究
16.
"After your examination, the doctor will place all your medical documents into this envelope and send it direct to the office"
体检医生在对你体检后将把填完的体检材料放进此信封内,然后直接寄往上述写明的办事处
17.
gasket and similar joint, assortments or sets, of any materials dissimilar in composition, put up in pouches, envelopes, boxes etc
密封垫及类似接合衬垫,成套或各种不同种类,任何结构不同材料制成,装于袋、套、箱等
18.
The machining craft of the main pump components and the method to select mating material are stated in detail as well.
同时对泥浆泵过流部件的制造工艺、封接合面材料的选取作了详细说明。