1.
Preparation of Nylon 6 with High Viscosity by Chain-extension during Melting Extrusion
熔融挤出扩链反应制备高粘度尼龙6
2.
Equipment assembling technique for modern BOPET lines' chip melting and extruding system
现代BOPET生产线熔融挤出系统配置技术
3.
Study on the Extrusion Moulding of Ultrahigh Molecular Weight Polyethylene under Ultrasonic Irradiance;
超高分子量聚乙烯的超声熔融挤出成型研究
4.
Research on Grafting Maleic Anhydride onto Polyolefin with Melt Extrusion
聚烯烃熔融挤出接枝马来酸酐的研究进展
5.
Solid Melting Section on the Ram Extruder Based on ANSYS
基于ANSYS的柱塞挤出机熔融段研究
6.
This paper introduces an analytical melting model for extrusion to calculate the melting rate and predict the meltingcapacity of screw.
根据挤出熔融模型用解析法计算熔融速率,预测螺杆的塑化能力。
7.
Melt spinning involves melting the nylon in an inert atmosphere, controlling the extrusion and solidification of the melt, and collecting the extruded filaments.
熔纺包括尼龙在惰性气体中的熔化、控制熔融体挤出和固化、卷绕挤出的长丝等几个过程。
8.
Study on the Melt Graft-Reacting Extrution of PE or EPDM with MAH and the Alloying of PA Toughened by the Grafts;
MAH与PE或EPDM熔融接枝反应挤出和挤出物增韧PA合金化的研究
9.
The Theory and Visualization of Submacroscopic Melting Process in Single-Screw Extrusion;
单螺杆挤出的亚宏观熔融理论及可视化研究
10.
Visualization of Melting Mechnism and Phase Transition for Single Screw Extrusion with Screw Being Cooled;
螺杆冷却时单螺杆挤出过程熔融机理及相变行为的可视化研究
11.
Study on Melt Mixing of Nano Powder and Polymer in Co-Rotating Twin Screw Extruder;
纳米粉体与聚合物在同向双螺杆挤出机中的熔融混合研究
12.
Study on Driving Power Consumption of Solid Conveying and Melting Process in Conical Twin-Screw Extruder;
锥形双螺杆挤出机固体输送段和熔融段物料输送功率消耗的研究
13.
After heating and friction heating by the rotating screw, the resin turns to a melt and is extruded through a die in the form of a cylindrical tube (parison).
塑料经加热及螺杆转动的摩擦力变为熔融后，从模头挤出，成为圆筒状。
14.
Based on the melting experiments of PP powder in twin-screw extruder, the melting capacity of different screw-thread sets and the revolution of the screw was studied.
通过对PP粉料在双螺杆挤出机中的熔融实验，研究了不同螺纹组合和螺杆转速对物料的熔融能力。
15.
Lava was ejected from the volcano.
熔岩受到压挤而从火山口喷射出来。
16.
THE FLOW ANALYSIS OF POLYMER MELT IN CO-EXTRUSION DIE
共挤出机头中的聚合物熔体流动分析
17.
Study on Tandem Extrusion System of Single Screw-Melt Pump;
单螺杆—熔体泵串联挤出系统的研究
18.
Influence of type of extruders on melt properties of PP
挤出机类型对聚丙烯熔体性能的影响