1.
continuous bright carburizing quenching furnace
连续式光辉渗碳淬火炉
2.
Analysis of abnormal distortion of driven bevel gear after carburizing and hardening
从动锥齿轮渗碳淬火后异常畸变分析
3.
Method for reducing black structure in 20CrMnTi steel after carburizing and quenching
减少20CrMnTi钢渗碳淬火黑色组织的方法
4.
EXAMINATION AND ANALYS OF THE GRINDING AFFECTED LAYER OF CARBURIZED AND HARDENED GEARS
渗碳淬火齿轮磨削变质层的检测与分析
5.
Analysis and Measure of Prick Gear Carburizing Quenching Distortion of Automobile Rear Bridge
汽车后桥被动锥齿轮渗碳淬火变形分析与对策
6.
Residual Stress of Carbonized and Quenching Gear Considering Phase Transformation Plasticity
考虑相变塑性影响的渗碳淬火齿轮的残余应力
7.
Optimization of Cam's Carburizing and Quenching Technology of High-powered Marine Diesel Engine
大功率船用柴油机凸轮渗碳淬火的工艺优化
8.
Study on the Effect of Material and Technology Factors on the Distortion of Carburizing and Hardening Gears;
材料和工艺因素对渗碳淬火齿轮畸变影响的研究
9.
The Carburization Quenching Distortion Rule and Mechanism Study of a New Kind of Micro-distortion and High Strength High Toughness Bainitic Steel;
新型微变形高强韧贝氏体GDL-1钢渗碳淬火变形规律的探索
10.
Employing abrasive machining for the form of the gear and intellective-control carburizing and quenching technology for the surface, the gear is with high intensity, strong tenacity and wearability.
齿轮齿形采用磨齿加工，齿面采用智能控制渗碳淬火技术，齿轮的强度高、韧性和耐磨性好。
11.
The case-hardening or carburizing process is in wide use.
表面淬火或渗碳法应用十分广泛。
12.
Research on Microstructure and Properties of Carburizing Alloy Steel Treated by Intensive Quenching Process
渗碳合金钢强烈淬火组织与性能研究
13.
Research on Carburized Stress Quenching and Its Influence on Properties
渗碳应力淬火及其对性能影响的研究
14.
Controlled Atmospheres for Quenching and Carburizing of General Machine Parts
通用机械零件淬火及渗碳用控制气氛
15.
Early Failure of Steel Parts and Uncontrolled Microstructure after Carburizing,Post-Quenching and Tempering
钢件渗碳淬回火组织失控及构件的早期失效
16.
Effect of Austerpering After Carburizing on Microstructure and Property of 18Cr2Ni4WA
18Cr2Ni4WA渗碳后等温淬火对组织与性能的影响
17.
The heat treatment technology of carbo- nitriding of steel has the characteristic of lower treatment temperature and direct quenching.
钢的碳氮共渗热处理工艺具有共渗温度低、直接淬火等特点。
18.
Sim? ilarly, an increase in case depth, particularly uneven case depth in case hardening steels, increases warpage on quenching.
与此类似，渗碳层厚度越大，特别是对于渗碳层厚度不一的渗碳用钢，淬火时更易产生翘曲。