1) pressure beneath foundation
![点击朗读](/dictall/images/read.gif)
基底反力分布
1.
The numerical analysis of spread foundation's pressure beneath foundation on rock foundation
岩石地基上扩展式基础基底反力分布数值分析
2) foundation pressure distribution
![点击朗读](/dictall/images/read.gif)
基底压力分布
3) contact pressure
![点击朗读](/dictall/images/read.gif)
基底反力
1.
Simulated tests indicate that the deformation center and contact pressure center of the thick raft foundation under the vertical load of L-shape tall building with confirmed dimensions are near the corner of the L-shaped and spread around.
室内大型模拟试验表明,给定几何尺寸的L形高层建筑下的筏基变形特征和基底反力分布规律是以L形的拐角附近为中心向四周扩散,但地基反力的扩散范围只有到裙房两跨的位置。
2.
Analysis of rigid rectangular plate on cross-anisotropic with transferring matrix,discuss the influence of the following factors,two Yong s moduli E v,and E h,shear modulus G v,two Poisson s ratios u h,and u vh ,n and m,on the settlement and contact pressure;analyze layered subsoil and compare it with the normal method at the same time.
采用传递矩阵法分析横观各向同性地基上的刚性矩形板 ,分析竖向的弹性模量Ev、水平向的弹性模量Eh、竖直面上的剪切模量Gv 以及Eh 和Ev 的比值n、Gv 和Ev 的比值m、水平向应力引起的正交水平向应变的泊松比uh、竖直向应力引起的水平向应变的泊松比uvh对沉降和基底反力影响 ;同时采用成层地基进行分析 ,将其计算结果与常规方法中采用对弹性模量和泊松比在计算深度内按深度加权平均的计算结果进行比
3.
Analyze rigid circular plate on cross anisotropic subgrade with transferring matrix,discuss the influence of the following factors,two Young s moduli E\-v,and E\-h,shear modulus G\-v,two Poisson s ratios u\-h,and u\-\{vh\} n,and m,on the settlement and contact pressure;analyze layered subsoil and compare it with the normal method at the same time.
采用传递矩阵法分析横观各向同性地基上的刚性圆板 ,分析竖向的弹性模量Ev、水平向的弹性模量Eh、竖直面上的剪切模量Gv 以及Eh 和Ev 的比值n、Gv 和Ev 的比值m、水平向应力引起的正交水平向应变的泊松比uh、竖直向应力引起的水平向应变的泊松比uvh对沉降和基底反力影响 ;同时采用成层地基进行分析 ,将其计算结果与常规方法中采用对弹性模量和泊松比在计算深度内按深度加权平均的计算结果进行比
4) distributional reaction
![点击朗读](/dictall/images/read.gif)
分布反力
1.
Finite element calculation of elastic foundation plate considering distributional reaction of foundation;
考虑地基分布反力的弹性基础板有限元计算
补充资料:锅炉、压力容器、压力管道及特种设备定期检验
锅炉、压力容器、压力管道及特种设备定期检验
periodic inspection of boilers, pressure vessels, pressure piping and special equipment
guolu YOli侧飞扣1 YOli gLJal对印ji tez陌叩劝以拍1 dingqi】,on四n锅炉、压力容器、压力管道及特种设备定期检验(peri诫c inspectionof城le。,p~切reves-Sels,p~二piPing ands衅过闪uiplr屺nt)为保证设备的安全使用,规定设备必须按一定周期进行法定的、强制性的检验。定期检验由政府设立的检验所、使用单位或行业检验站进行。检验单位及检验人员必须具有与所检设备相适应的资格。设备使用单位应该建立定期检验制度,做好检验计划,按时向检验单位提出申请。检验单位应该保证及时进行检验,检验按有关检验规则进行。检验时,设备使用单位应做好配合工作,提供必要的运行资料。检验完毕,检验单位要出具检验报告,对设备能否使用,要作出明确结论。如设备有缺陷,要提出是否修理、监护使用和报废的处理意见。锅炉压力容器安全监察机构根据检验机构的报告,发使用许可证书。有缺陷的,责令使用单位修理,修理后检验仍不符合安全要求的,则通知报废。使用单位逾期不进行定期检验,锅炉压力容器安全监察机构有权停止其设备运行。(陈亦惠)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条