1) In-situ synthesized composites
原位合成复合材料
2) in-situ fibrillation composite
原位成纤复合材料
1.
It was employed that changing the processing temperature, screw speed and draw rate in order to study how the processing conditions influence PP/N6 in-situ fibrillation composite.
分别用不同的加工温度、挤出螺杆转速、牵引速率在单螺杆挤出机中挤出PP／N6（聚丙烯／尼龙6）共混物，得到不同加工条件下的PP／N6原位成纤复合材料。
2.
Some thermoplastics such as poly(ethylene terephthalate),polyamide-66,polyamide-6,ultra high molecular weight polyethylene,poly(phenylone sulfide) and poly(ethylene naphthalate) were adopted as fibrillation polymers,and the preparing method and technology of in-situ fibrillation composites based on polypropylene by using these fibrillation polymers were summarized.
以聚对苯二甲酸乙二酯(PET)、尼龙(PA)66、PA6、超高分子量聚乙烯(UHMWPE)、聚苯硫醚(PPS)、聚萘二甲酸乙二酯(PEN)等热塑性树脂为成纤聚合物,综述了利用这些成纤聚合物制备聚丙烯(PP)基原位成纤复合材料的方法、技术及复合材料的结构特征、力学性能。
3) in situ composite
原位复合材料
1.
Study on the orthorhombic experiment of the AlN/ZL101 In Situ composite;
AlN/ZL101原位复合材料的正交实验研究
2.
In order to gain higher magnetic performance and solve air pollution problems in extraction process of Fe-Cr fibers,cupreous body of Cu-13Fe-2Cr in situ composite materials were corrupted by using chemical extraction.
为解决Fe-Cr纤维提取过程中容易造成空气污染的问题,使得到的纤维具有较高的磁学性能,采用化学萃取法腐蚀掉Cu-13Fe-2Cr原位复合材料中的铜基体,制备了Fe-Cr金属纤维;通过调整硝酸与双氧水比例抑制NO2的产生;通过改变清洗方式使纤维具有较高的磁性。
3.
Fe-Cr fibers were extracted from Cu-16Fe-2Cr in situ composite wires in 65% nitric acid.
Fe-Cr纤维由Cu-16Fe-2Cr原位复合材料硝酸法萃取得到。
4) in-situ composites
原位复合材料
1.
Microstructure and properties of Cu-Fe-Ag in-situ composites;
Cu-Fe-Ag原位复合材料的组织和性能
2.
Effects of micro-alloying on microstructure and mechanical properties of Cu-15Cr in-situ composites
微合金化对Cu-15Cr原位复合材料组织和性能的影响
3.
Non-isothermal crystallizations of the polycaprolactam chain segment grafted carbon fibre(CF)/monomer casting(MC) nylon 6 in-situ composites were investigated at different cooling rates by means of differential scanning calorimetry(DSC).
采用差示扫描量热(DSC)法,研究表面接枝聚己内酰胺链段的碳纤维(CF)/单体浇铸(MC)尼龙6原位复合材料,以及其在不同冷却速率下的结晶动力学特性;用Jeziorny法和Liu法对它们的非等温结晶动力学进行处理。
5) in situ composites
原位复合材料
1.
Preparation and properties of polylactide/nano-silica in situ composites;
聚乳酸/纳米二氧化硅原位复合材料的制备和性能
2.
The results show that In Cu-11Fe-4Cr in situ composites,E(Cu)
采用选择腐蚀技术,提取了Cu-11Fe-4Cr原位复合材料中Fe-Cr纤维,并测定了其电极电位。
3.
A series of in situ composites were obtained by melt blending thermoplastic resin polysulfone (PSF) and four thermotropic liquid crystalline polymers (TLCP) using three methosd: (1)extruded by melt index machine directly; (2)extruded by a single screw extruder; (3)blended the raw materials by a mixer first, then extruded by single screw extruder.
将热塑性树脂聚砜与４种自制的热致液晶聚合物熔融共混，制备原位复合材料，采用了３种制样方法：①毛细管直接法；②单螺杆直接挤出法；③先用混合机混合均匀，再用单螺杆挤出。
6) Insitu Composite
原位复合材料
1.
The compatibility of the insitu composite of Polycarbonate(PC) and liquid crystalline copolyester can be improved by adding the multiblock copolymer prepared from PC and LC copolyesteramide oligomer.
通过加入液晶聚酯酰胺和聚碳酸酯的多嵌段共聚物，可以有效地降低基体聚碳酸酯的玻璃化转变温度，提高热致液晶高分子ＰＥＴ／６０ＰＨＢ与聚碳酸酯原位复合材料的相容性。
补充资料：原位
分子式：
CAS号：
性质：源于拉丁语。指在原来的，正常、自然的部位或位置。
CAS号：
性质：源于拉丁语。指在原来的，正常、自然的部位或位置。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条