1) Axial Melt Temperature Difference
轴向温差
1.
Experimental Study of Axial Melt Temperature Difference at Injection Screws
注射螺杆轴向温差的实验研究
2) axial error
轴向误差
1.
To meet the requirement of 100% on-line inspection of gears in mass production in automotive and motorcycle industry, the two-flank principle is used to check the gear radial errors(thickness, radial composite error, run-out and error burs)and the gear axial errors(mean helix error, helix error and taper error)to realize the quick on-line inspection of gear machining flaws.
针对汽车、摩托车齿轮生产企业大批量齿轮生产现场,实现在线100%快速检测需要,本项目采用双面啮合原理测量齿轮的径向误差(齿厚、径向综合偏差、径向跳动、毛刺等)和轴向误差(平均齿向偏差、齿向偏差、锥度误差),实现齿轮的制造缺陷的现场快速检测。
2.
This paper, part seven of "Analysis of Errors and Inspection Groups on Hobbing Gear", dis- cusses the reason why the axial error occurs, the mathematical model and the relation between tol- erance group Ⅲ and axial error.
这部分的主要内容是论述轴向误差的产生原因,数学模型以及轴向误差与第Ⅲ公差组之间的关系。
3.
In this paper,the existing best-fit calculation,so as to the existence of axial RMS minimum goal for the design of the match,the current method of calculating the axial error is discussed,pointing out that some places a little unreasonable,a more accurate calculation of the axis to the formula for calculating the error and gives the derivation process.
针对现有的吻合计算,存在以轴向RMS最小为设计目标的吻合,对目前计算轴向误差的方法进行了讨论,指出了某些稍不合理的地方,提出了一个较为准确的计算轴向误差的计算公式,并给出了推导过程。
3) axial differential expansion
轴向胀差
1.
The methods of calculating turbine axial differential expansion on-line and controlling axial differential expansion by c changing steam temperature increment were investigated.
研究了汽轮机轴向胀差的实时在线计算以及通过变温度速率控制胀差的方法。
4) axial force difference
轴向力差
1.
In order to investigate the influence of slot type of inner plate in liquid viscous coupling on hump phenomenon, the relations between the axial force difference on inner plates and the factors such as plate beveled edge, beveled edge height, the position of inner plate were simulated by the FLUENT software.
借助FLUENT软件模拟内盘片上轴向力差与内盘片倒角角度、倒角高度和内盘片在相邻外盘片间的位置的关系。
5) axial alignment tolerance
轴向偏差
1.
Research results indicate that when the single ball lens is used in the LD-ball lens-SMF system,the axial alignment tolerance is ±30 μm,the lateral alignment tolerance is ±1.
结果表明:当采用单球透镜时,所带来的轴向偏差为±30μm,横向偏差为±1。
6) axial aberration
轴向像差
补充资料：单轴各向异性
单轴各向异性是磁晶各向异性的最简单形式，即自发磁化的稳定方向（或易磁化方向）平行于一特殊晶轴。如六方晶系钴的自发磁化方向平行于 C轴(见晶体结构)，这就表现出强的单轴各向异性。磁性材料的单轴各向异性值一般都低于其磁晶各向异性值，为103erg/cm3量级。磁性材料经磁场热处理或强的冷加工而产生的感生各向异性，都属于单轴各向异性。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条