1) system cooling effect
系统冷却效果
2) Cooling effect
冷却效果
1.
Monitoring and analysis of cooling effect of block-stone embankment for Qinghai-Tibet Railway;
青藏铁路块石路基结构的冷却效果监测分析
2.
It has been proven that the structure of machine,the cooling effect ,the quality of cooling substance and the working noise,etc.
介绍了一种新型振动逆流式冷却(干燥)机的设计方法及其结构和工作原理,论述了该机的主要优点,表明了它在机器结构、冷却效果、冷却物质量及工作噪声等诸多方面均优于现有的逆流式冷却机,为冷却机的更新换代创造了条件。
3.
,the factors affecting cooling effect are analyzed in detail according to the principles of heat conduction,convection,radiation and the measures to improve cooling effect are put forward,such as improving sealing to reduce leakage,improving the ore distribution to restrain edge effect,and increasing layer height etc , which are very helpful to improve cooling efficienc
针对湘钢二烧带冷机鼓风冷却不充分 ,漏风严重等现象 ,通过对鼓风带冷机的全面测试 ,对影响带冷机冷却效果的因素从导热、对流、辐射综合传热及带冷机的工作方式进行了详细分析 ,并提出了加强密封以治理漏风 ,改进布料方式以抑制边缘效应和提高料层厚度等具体措施。
3) cooling effectiveness
冷却效果
1.
The investigation focused on the parameters affecting cooling effectiveness,which are dimensionless height of cooling passage h,dimensionless height of ripple board and dimensionless diameter of cooling holes d.
波纹板高度的变化对冷却效果的影响最为明显。
2.
The influences of the coolant flow blowing angle α on the effusion cooling effectiveness of a porous plate were investigated.
采用数值模拟方法研究了冷气流的入射角对致密多孔壁冷却效果的影响 ,通过 9个算例分析比较入射角为 3 0°,60°和 90°情况下的冷却效果 ,在每个入射下吹风比 M分别取为 0 。
3.
Research on the changing regulation of the cooling effectiveness of the porous lamellar tablet with the blowing ratio of the hot and cooling flow has been done.
研究了改变冷热气流吹风比对该型层板冷却效果的影响。
4) total cooling effect
总冷却效果
5) Cooling system
冷却系统
1.
Design of gating and cooling system in injection mould for LCD rear cover;
液晶显示器后盖注射模浇注与冷却系统设计
2.
Design of the cooling system of CD Injection Mould;
对光盘注塑模具冷却系统的研究与设计
3.
An on-line supervision system for water temperature difference and heat flux intensity in blast furnace cooling system;
一种高炉冷却系统水温差及热流强度在线监测技术
6) the cooling system
冷却系统
1.
Application of CAE in the cooling system of injection molding;
注射模冷却系统中的CAE技术应用
2.
As the property of the plastic,the structure of the plastic production and the parameter of the molding process vary greatly, the temperature required for the cooling system also differs.
注射模冷却系统的设计不但关系到塑件质量而且也关系到注射成型生产效率。
3.
The choice and estimation for the cooling system parameter in the engine cabin is guided.
快速而准确地指导发动机舱内冷却系统的参数选择与判定。
补充资料：Fogeffect(雾化效果)
fog effect (雾化效果)
雾化效果是3d的比较常见的特性，在游戏中见到的烟雾、爆炸火焰以及白云等效果都是雾化的结果。它的功能就是制造一块指定的区域笼罩在一股烟雾弥漫之中的效果，这样可以保证远景的真实性，而且也减小了3d图形的渲染工作量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条