1) strength toughness
强韧性分析
2) high strength and toughness
高强韧性
1.
Development of Microalloyed Intragranular Ferrite Steel With High Strength and Toughness;
晶内铁素体型高强韧性微合金非调质钢的进展
2.
A Study on Decarburization Trend of New High Strength and Toughness Spring Steels 40T and 44T;
新型高强韧性弹簧钢40T和44T脱碳倾向的研究
3) toughness
[英]['tʌfnis] [美]['tʌfnɪs]
强韧性
1.
Effect of Heat Input on Strength and Toughness of Welding Metal of High Strength Wire;
热输入对高强度气体保护焊丝焊缝金属强韧性的影响
2.
The characteristic parameters of high grade pipeline steels were investigated,and their effects on toughness were explored by means of mechanical testing and microstructural analysis as EBSD(Electron Backscattered Diffraction) and SEM.
利用力学实验及EBSD等微观分析手段,研究表征高钢级管线钢的特征参数,并探讨其对强韧性的影响。
4) strength-toughness
强韧性
1.
The dynamic strength-toughness of 9Cr-lMo-V-Nb-N steel;
9Cr-1Mo-V-Nb-N钢的动力强韧性
2.
In view of the improper matching of the strength-toughness for domestic petroleum drill pipe sub,the influence of the chemical compositions and metallurgical quality of 37CrMoE steel used for drill pipe sub on its mechanical properties,as well as the effect of the metallurgical quality on the hardenability,were analyzed.
针对国产石油钻杆接头存在强韧性配合不良的问题,试验研究了钻杆接头用37CrMoE钢的化学成分和冶金质量对其力学性能的影响,以及冶金质量对淬透性的影响。
3.
The steel selected for this investigation is spring steel 50CrVA for automobile in this paper,the appropriate duplex microstructure of lower bainite and martensite was obtained through isothermal quenching and low temperature tempeing heating treatment,then the effect of duplex microstructure and tempered troostite on strength-toughness of spring steel 50CrVA is compared.
以汽车用弹簧钢50CrVA为研究对象,通过等温淬火+低温回火热处理工艺获得适当比例的回火马氏体和下贝氏体的复合组织,并在此基础上比较复相组织和回火屈氏体对弹簧钢50CrVA强韧性的影响。
5) obdurability
[,ɔbdjuərə'biliti]
强韧性
1.
The qualitative factors such as paper structure,pulp performance and technological parameters of papermaking and the quantative representation of such physical-chemical properties as stiffness,obdurability and flattening can have direct or indirect influence on molding perfomance of paper container.
从纸页结构、纸浆性能、抄造工艺参数等诸因素的定性分析,定量表现在成纸的挺度、强韧性和平整性等理化性能,都对纸容器加工成型产生直接或间接的影响。
2.
The results show that the obdurability of 60Si2Mn treated by sub-zero treatment after quenching is better than the craft of high temperature quenching.
对 60Si2Mn冷冲模具钢采用常规淬火、高温淬火及淬火后深冷处理等热处理工艺进行强韧化对比试验,结果表明,经常规淬火深冷处理后其强韧性远超过高温淬火工艺,是一种实用性很强的强韧化工艺。
3.
This article has analyzed the reasons of the cracks on the H13 steel thicker mould produced during the quenching process, and pointed out that the proper heat treatment process is the key point to ensure the optimized obdurability and thermal fatigue resistance obtained, as well as the key point to ensure the quenching quality.
通过对H13钢加厚模在淬火过程中产生裂纹的原因进行分析,指出合适的热处理工艺是确保获得最佳的强韧性及热疲劳抗力的关键,也是确保淬火质量的关键。
6) strength and toughness
强韧性
1.
Study on the strength and toughness of low-canbon multiphase steel;
低碳复相组织钢的强韧性研究
2.
Study on strength and toughness of seam of HSLA steel;
低合金高强钢焊缝强韧性研究
3.
Comparative studies on strength and toughness of SDH8 and H13 hot work steel;
热作模具钢SDH8与H13的强韧性对比研究
补充资料：强韧
1.见"强韧"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条