|
|
1) lithologic characters
泥岩百分比含量
1.
Based on the analysis on seismic attributions,an analysis method of seismic attributes and prediction method of lithologic characters based on a BP artificial neural network were proposed for forecasting the mudstone percentage content of coal roof.
从地震属性分析入手,提出了用于煤层顶板泥岩百分比含量预测的地震属性分析方法和BP人工神经网络岩性预测方法。
2) sand percentage in section
剖面砂岩百分比含量
3) sand content
砂岩百分含量
1.
Based on the regional geological background in the North Yellow Sea Basin and the principle of velocity analysis,we obtained the information of interval velocity,average velocity,sand content,etc,which was used to interpret and calculate the velocity spectrum of the north Yellow Sea basin.
概述了北黄海盆地的区域地质背景和速度分析的原理,通过对北黄海盆地速度谱的解释和计算,得到了层速度、平均速度、砂岩百分含量等信息,利用这些速度资料识别多次波、辨别坳陷区和隆起区,进行时深转换、构造分析以及岩性分析,为北黄海盆地地震资料解释、沉积相分析以及资源量计算提供可靠的依据。
2.
The interval velocity,time-depth conversion and sand content of the Zhongjiannan Basin in the South China Sea are calculated based on interpretation of velocity spectra.
在大量速度谱解释的基础上,分别计算了南海中建南盆地的层速度、时深转换和砂岩百分含量,并对盆地5套地层的层速度平面图进行了分析。
4) rock quality percentage(RQP)
岩石质量百分比
5) mudstone content
泥岩含量
1.
Therefore,it is necessary to study the influences of saturation manners and mudstone content on seepage coefficient of rockfill.
因此有必要探讨饱和方式和泥岩含量对堆石料渗透系数的影响。
6) Percentage content
百分含量
1.
n this paper,the gold or platinum percentage content of alloy gold or platinum detected by method of density are compered with the results detected by chemical analysis and devices.
本文通过贵金属金、铂合金配比，密度法测试百分含量与化学分析及仪器检测百分含量进行比较，测试结果准确度达到０。
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|