1) shear-resistant property
抗剪切性能
1.
Influences of 1-dodecene content on the relative molecular mass and shear-resistant property of the copolymer and the ultrasonic shearing on the relative molecular mass distribution of the copolymer were studied.
5);辛烯用量对提高共聚物的抗剪切性能无明显作用;共聚物被超声剪切后,其相对分子质量分布为双峰分布,不属于拓扑断裂模型。
2) high temperature shear performance
高温抗剪切性能
1.
Through comparative analyse all of exist test\'s workload of the test,mechanics index and mechanical properties,The use of axial partial loading test evaluate lasphalt mixture in the high temperature shear performance.
本文研究的目的在于提出一种更加适合于评价沥青混合料高温抗剪切的简单性能试验方法,通过对现有各种试验方法的试验工作量、力学特性和力学指标的对比分析,提出采用轴向局部加载试验评价沥青混合料的高温抗剪切性能。
3) shearing resistance
抗剪切性
1.
Hydrophobically associating polymer solution has special shearing resistance performance because of introduced associating base group, so there is a wide application prospect in oil gas exploitation.
疏水缔合聚合物分子链上疏水基团的引入使其溶液具有独特的抗剪切性能,从而在油气田开采领域具有广阔的应用前景。
2.
31 s-1),the shearing resistance,and the oil displacement efficiency of high concentrated(2.
31 s-1)、抗剪切性、弹性及岩心驱油效果作了比较研究。
4) anti-shearing
抗剪切性
1.
The results show that the expansion degree and anti-shearing of the cross linked starch after hydrolysis increases, pasted temperature and viscosity decreases, but the stability of viscosity gradually heightens along with the increase of hydrolysis degree.
对交联淀粉采用酶解和发酵处理 ,研究酶解和发酵后交联淀粉的应用性质 ,结果表明 :交联淀粉酶解后其溶胀度和抗剪切性随DE值增加而增加 ,糊化温度降低 ;随酶解程度的增大 ,交联淀粉的粘度下降 ,粘度稳定性逐渐提高。
5) shear properties
剪切性能
1.
Dynamic shear properties of the tungsten heavy alloys containing 90% to 97% W (mass) were investigated using a hat-shaped specimen on the Hopkinson rod of Split Compression at a shear strain rate of 105 s-1.
利用帽形试样在Hopkinson压杆上测试钨合金动态剪切应力应变关系,研究了钨含量在90%~97%(质量分数)范围内,应变率约为105s-1时,钨含量对动态剪切性能的影响。
2.
In this paper,shear properties of 3-D braided composites and C-L fiber reinforced composites after moisture absorption behaviors are studied.
本文对三维四向编织复合材料和长碳纤维复合材料吸湿后的剪切性能进行了研究。
3.
The shear properties of MBWK fabrics are most important as far as a forming .
在MBWK织物的力学性能中，剪切性能尤为重要，它直接决定了该织物对三维曲面的成型性能。
6) shear property
剪切性能
1.
This paper is to optimize flexibility rubber material from silicone rubber、chloroprene rubber and butadiene rubber blends or modified nature rubber,according to their shear property at low temperature(-30?℃)and adhesive strength.
主要从低温剪切性能(-30℃)和粘接性能两方面,对硅橡胶、氯丁/顺丁橡胶并用和天然橡胶低温改性三种方案进行性能比较,优选弹性材料橡胶基材。
2.
The influencing factors such as temperature (25℃-900℃), cooling way, interface roughness and interface adhesive agent on bond shear property are studied.
对先粘结后高温与先高温后粘结两种类型的129块Z形新旧混凝土粘结试件进行了直剪试验,主要考察了温度(常温到900℃)、冷却方式、界面粗糙度和界面剂对粘结面剪切性能的影响。
3.
The influencing regularities of several main factors including temperature, cooling process, roughness of interface and interface adhesive on adhesive shear property were summarized.
为了研究高温对新老混凝土粘结性能的影响,本文对既有混凝土经历高温后再与新混凝土粘结和新老混凝土粘结后再经历高温两种类型的Z形粘结试件进行了剪切试验研究,总结了影响粘结面剪切性能因素(温度、冷却方式、界面粗糙度和界面剂)的影响规律,提出了温度对粘结面剪切强度和剪应力滑移关系的影响计算公式,建立了高温后粘结剪切强度的多因素统一计算公式。
补充资料：高温
较高的温度，在不同的情况下所指的具体数值不同，例如在某些技术上指几千摄氏度以上，在工作场所指32摄氏度以上。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条