1) WC-Co/SiC coating
WC-Co/SiC涂层
1.
It has introduced the composition,technology,characteristic and application effects of few of composite hard alloy material such as WC-Co/TiC-Al2O3, WC-Co/diamond,WC-Co/SiC coating etc.
介绍了WC-Co/TiC-Al2O3、WC-Co/金刚石、WC-Co/SiC涂层等几种硬质合金复合材料的成分与工艺、性能和应用效果。
2) WC-Co coating
WC-Co涂层
1.
Evaluation on the plasma-sprayed WC-Co coating using ultrasonic wave technology;
等离子喷涂WC-Co涂层的超声波评价
2.
Investigation in WC-Co coating of detonation spraying and its application on screw drills;
爆炸喷涂WC-Co涂层研究及在螺杆钻具中的应用
3.
Properties of WC-Co coating deposited by high velocity oxy-air fuel spraying;
氧气-空气混合助燃超音速火焰喷涂WC-Co涂层性能研究
3) WC/Co coating
WC/Co涂层
1.
The wear-off characteristics of both the gray iron and its WC/Co coating was investigated.
用超音速火焰喷涂方法在灰口铸铁表面进行了WC/Co涂层的喷涂,对灰铸铁表面及在其上喷涂的WC/Co涂层摩擦磨损特性进行了研究。
4) WC-12Co coatings
WC-Co涂层
1.
The WC-12Co coatings were sprayed by different super-sonic thermal spraying processes of Supersonic Plasma Spraying(HEPJet) and two kind of HVOF(JP5000,DJ-2700).
用超音速等离子喷涂(HEPJet)和两种进口高速氧燃气火焰喷涂设备(JP-5000和DJ-2700)制备WC-Co涂层,进行了30(°)和90(°)攻角的冲蚀磨损对比试验,分析了涂层的SEM磨损形貌。
2.
The WC-12Co coatings were sprayed by different supersonic thermal spraying processes of supersonic plasma spraying (HEPJet) and two kind of high velocity oxy-fuel spraying (HVOF)(JP-5000, DJ-2700).
用超音速等离子喷涂(HEPJet)和两种进口高速氧燃气火焰喷涂(HVOF)设备(JP-5000和DJ-2700)制备WC-Co涂层,进行了孔隙率、显微硬度、结合强度及30°和90°攻角的冲蚀磨损对比实验,分析了涂层的SEM磨损形貌。
5) WC-17%Co coating
WC-17%Co涂层
1.
The coating has the good ware resistance,and the ware mechanism of WC-17%Co coating is mainly delaminated by ware.
研究了等离子喷涂WC-17%Co涂层的显微结构、相组成、平均硬度和磨损形貌、耐磨性能。
6) WC-12%Co coating
WC-12% Co涂层
1.
Nanostructured and conventional WC-12%Co coatings were deposited on stainless steel substrate using atmospheric plasma spraying.
利用大气等离子喷涂技术制备了纳米和微米WC-12% Co涂层,采用SRV摩擦磨损试验机考察了纳米和微米WC-12%Co涂层在干摩擦条件下分别与Si3N4陶瓷球和不锈钢球配副时的摩擦磨损性能。
补充资料：WC-TiC-Co hard alloy
分子式：
CAS号：
性质：又称钨钛钴合金或YT合金。碳化钨、碳化钛和金属钴组成的合金。按碳化钛含量，可分为高钛(25％～40％)、中钛(10％～20％)和低钛(4％～6％)三类合金。它比碳化钨钴合金具有较高的抗氧化性，硬度和耐磨性，而抗弯强度、冲击韧性等则有所降低。主要用作切削加工钢材的工具。
CAS号：
性质：又称钨钛钴合金或YT合金。碳化钨、碳化钛和金属钴组成的合金。按碳化钛含量，可分为高钛(25％～40％)、中钛(10％～20％)和低钛(4％～6％)三类合金。它比碳化钨钴合金具有较高的抗氧化性，硬度和耐磨性，而抗弯强度、冲击韧性等则有所降低。主要用作切削加工钢材的工具。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条