1) cube texture double orientation silicon steel
立方织构双取向硅钢
3) double oriented silicon steel
双取向硅钢板
4) oriented silicon steel
取向硅钢
1.
Effect of Si_3N_4 tensile coating on performance of oriented silicon steel;
氮化硅张力涂层对取向硅钢性能的影响
2.
Effect of tensile coatings through electrodeposition on properties of oriented silicon steel;
电沉积涂层对取向硅钢性能的影响
3.
Influence of nitriding modes and ammonia on nitrogen content of oriented silicon steel
渗氮方式及氨气对取向硅钢氮含量的影响
5) grain-oriented silicon steel
取向硅钢
1.
For preventing the edge cracking produced in hot-rolling grain-oriented silicon steel,some measures are adopted: controlling oxygen concentrate and hold time in atmosphere when slab heating above 1 200℃,adjusting reduction and rolling temperature of roughing mill,carrying out width reduction and brink heating,changing de-formation energy of material and inhibiting brink fish scale-type defect.
川崎取向硅钢存在热轧板边裂问题。
2.
The calculation of single crystal magnetic induction coefficients from measured texture and magnetic induction data in a grain-oriented silicon steel strip has been discussed.
对由取向硅钢薄带的磁感和织构实测数据计算其单晶磁感系数进行了探讨。
6) grain oriented silicon steel
取向硅钢
1.
Local nitridation treatment was achieved on the surface of grain oriented silicon steel by laser local nitridation method.
采用激光氮化方法 (LN方法 )对取向硅钢表面进行局域线状氮化处理 ,引入气态氮作为合金化元素 ,研究了激光工艺参数对硅钢表面氮化物形成的影响·对传统观察磁畴的方法进行了改进 ,研制了一种新型的Fe3 O4磁流体 ,这种磁流体不仅能进行适时观察磁畴结构 ,而且还实现了带膜磁畴观察·利用XPS方法及Fe3 O4磁流体磁畴观测方法对处理后的样品进行了检测及磁畴观察·结果表明 :通过控制激光工艺参数可实现取向硅钢的激光氮化 ,在取向硅钢表面生成了Fe4N和Fe3 N两种氮化物 ;氮化处理后 ,硅钢片的磁畴结构有所细化 ,从而可以改善取向硅钢的性能 ,降低取向硅钢的铁损 ;氮化样品经 6 0 0℃ ,3h保温时效退火处理后 ,磁畴结构基本保持不变 ,这说明氮化处理可以使取向硅钢的高温时效性有所改善
2.
By means of TEM observation and EDAX analysis, the morphology of microstructures and precipitated inhibitor particles in high induction grain oriented silicon steels had been studied.
采用透射电镜及能谱分析等方法，研究了高磁感取向硅钢中微观结构与析出抑制剂质点的形态，证实铸坯经１３００℃与１３６０～１３８０℃加热轧制后硫化物的析出区域（包括位错、层错及晶界、亚晶界等处）和析出数量未产生差异，但１３００℃加热时，常化后ＡｌＮ的析出更弥散，其析出区域与硫化物的情况类似。
3.
The paper described the status quo ante,status in quo and development of the grain oriented silicon steel production in China.
本文叙述了我国取向硅钢生产初期的教训,现在的技术水平和设备条件。
补充资料：立方织构
cubetexture：经冷轧并退火的金属薄板，有时出现这样一种织构，即各晶粒的（100）晶面于轧制平面重合，[001]晶向与轧制方向平行，通常写为（110）[001]织构，称之为“立方织构”。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条