1) trigger resistance
触发电阻
1.
And the effects of different polarity combinations,trigger pulse amplitudes and trigger resistances on trigger characteristics of the trigatron have been derived.
实验结果表明:新型触发管开关获得最佳触发特性所需的极性组合应为异极性组合,触发电压幅值范围为自击穿电压的30%～50%,为兼顾触发电流和保护触发器,触发电阻值应为50～100Ω,验证了触发管开关击穿机制的已有认识。
2) trigger gap resistance
触发间隙电阻
3) contact resistance
接触电阻
1.
Stable distribution analysis to statistical evaluation of contact resistance in aluminum alloy spot welding;
基于稳定分布的铝合金点焊接触电阻
2.
On the contact resistance between graphite/polypropylene composite plate and carbon paper;
石墨／聚丙烯复合板与碳纸间的接触电阻
3.
Study of prediction method for contact resistance based on experiment constitutive relation;
基于实验本构关系的接触电阻预测方法研究
4) interfacial contact resistance
接触电阻
1.
The electrochemical methods were investigated in a simulated PEMFC environment and the volt-ampere technique was applied to measure interfacial contact resistance between the sample and carbon paper.
以304不锈钢为研究对象,采用电化学方法测定其在模拟PEMFC环境下的极化曲线和对应于PEMFC工作电位下的恒电流极化曲线,用伏安法测量304不锈钢表面氧化膜/钝化膜与碳纸之间的接触电阻。
2.
The 304 stainless steel treated by electroplating Cr and plasma-assisted nitriding processes was investigated by electrochemical methods in the simulated PEMFC environments, and interfacial contact resistance between the samp.
测定了经过镀铬后再离子氮化的304不锈钢在模拟PEMFC环境下的电化学性能,测量了氮化层与碳纸之间的接触电阻。
3.
The interfacial contact resistance between the sample and carbon paper are measured with volt-ampere technique.
以304不锈钢做为研究对象,测定了其在模拟PEMFC环境下的极化曲线,极化时间分别为4 h和10 h的交流阻抗谱,用伏安法测量了304不锈钢表面氧化膜/钝化膜与碳纸之间的接触电阻。
5) contacting resistance
接触电阻
1.
In order to reduce contacting resistance of bridge shaped contact and lower down temperature rise,improvement design was carried out for DW450-1100 universal circuit breaker bridge shaped structure.
为减小桥形触头的接触电阻,降低温升,对DW450-1600万能式断路器的桥形触头结构进行了改进设计。
2.
In order to determining the fire risk of plug and receptacle in different connecting resistance,the plugs rated 10 A and 16 A are used to study the temperature rising in the different contacting resistance and current.
为了确定插头插座在不同接触电阻情况下的火灾危险性,选用了常用的额定电流分别为10A和16A的两种插头插座,研究在不同的接触电阻条件下以及在相同的接触电阻下通过不同电流时插头插座的升温情况。
3.
In order to reduce the contacting resistance of contacts,to reduce temperature rise of contacts,improved design was made to the structure of contact.
为减小触头的接触电阻,降低触头的温升,对触头的结构进行了改进设计。
6) Contact Resistance
触点电阻
1.
Relay Contact Resistance Dynamic Testing;
继电器触点电阻的动态测试
补充资料：触发
1.触动引发。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条