1) angle of layer
铺层角度
1.
ince changing the angle of layer of performs will have an effect on the mechanical property of the composite,flax fiber was used as the reinforcing material in preparing the prefabricated material with polylactic acid fiber which had been subjected to opening,blending and carding.
针对预成型件的铺层角度对复合材料力学性能产生影响的问题,以亚麻纤维为增强体,与聚乳酸纤维通过开松、混合、梳理工序制成预成型件后,采用模压成型工艺制备了亚麻纤维/聚乳酸复合材料。
2) angle of fabric layer
织物铺层角度
1.
The results show that the longitudinal flexural strength increases while the transverse compressive strength decreases with increasing the number of fabric layer at certain extent; The effects of angle of fabric layer on longitudinal flexural strength and transverse compressive strength are also different.
研究表明:随着织物铺层层数在一定范围内的增多,织物增强水泥基复合材料的纵向抗折强度逐渐增大,而横向抗压强度却逐渐下降;织物铺层角度对织物增强水泥基复合材料纵向抗折强度和横向抗压强度有不同影响,在所试验的范围内,纵向抗折强度以45°织物铺层角度为最好,0°的次之,90°的最差,而横向抗压强度却以0°织物铺层角度为最好,90°的次之,45°的最差;织物铺层位置对织物增强水泥基复合材料纵向抗折强度和横向抗压强度的影响在不同的情况下有较大的差别。
3) ply angles
铺层角
1.
Sensitivity of the eigenvalues to the ply angles for composite plate;
层合板振动特征值对铺层角的灵敏度
4) ply stacking angle
铺设角度
1.
A comparison of acoustic emission characteristics in typical ply stacking angle of UHMWPE/LDPE composites;
典型铺设角度UHMWPE/LDPE复合材料的声发射特性比较
5) ply splice angle
铺层拼接角
1.
Three types of specimen containing v-notch were cut from laminates of different ply splice angle.
从三种不同铺层拼接角层合板上切取含缺口的剪切试件,通过实验测定了其载荷-位移曲线,得到了剪切强度值。
6) thickness of additional layer
加铺层厚度
1.
By the re seasch of former pavement remainder life - span, the total structural capacity of additional pavement was on relations with additionl layer and existing pavement was fully considered, and calculate the thickness of additional layer is based on.
通过研究旧路面的剩余寿命,在充分考虑加铺路面 总的结构能力、加铺层结构能力和旧路面有效结构能力三者之间关系的基础上,计算加铺层厚度。
补充资料：铺层器
分子式：
CAS号：
性质：又称铺层器。在平板支持物上，将固定相及黏合剂制成的浆状物均匀地涂布成薄层，制成薄层板的装置。薄层涂布器大致可分为固定式涂布器和移动式涂布器。有手工操作的，也有自动涂布装置。
CAS号：
性质：又称铺层器。在平板支持物上，将固定相及黏合剂制成的浆状物均匀地涂布成薄层，制成薄层板的装置。薄层涂布器大致可分为固定式涂布器和移动式涂布器。有手工操作的，也有自动涂布装置。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条