说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 初熔温度
1)  incipient melting temperature
初熔温度
1.
The incipient melting temperature of DZ68 alloy was confirmed between 1 240 ℃ and 1 260 ℃ by metallographic analytical method.
运用金相分析法确定了DZ68合金的初熔温度范围为1 240~1 260℃。
2)  initial melting-point temperature
初熔温度(仪)
3)  initial melt temperature
熔体初始温度
1.
Simulation study of effects of initial melt temperature on microstructure of liquid metal Na during solidification processes;
熔体初始温度对液态金属Na凝固过程中微观结构影响的模拟研究
4)  melt temperature
熔体温度
1.
Prediction of Injection Pressure and Melt Temperature of Injection Molding by Radial Basis Function Network;
基于神经网络技术的注塑成型注射压力和熔体温度预测
2.
Effects of Melt Temperature on Solidified Structure of Sn-Sb Peritectic Alloy in Ultrasonic Field;
超声场下熔体温度对SnSb合金凝固组织的影响
3.
The stress distribution of polycarbonate injection molded parts is tested by the photo-elastic experiment under different gate type and different melt temperature,and the tensile strength and luminous transmittance are tested.
用光弹实验测试不同浇口类型、不同熔体温度下聚碳酸酯透明注塑制品的应力分布,并测试了制品的拉伸强度和透光率。
5)  melting temperature
熔化温度
1.
Study on size effect of melting temperature of Pb nanowires;
铅纳米线熔化温度的尺寸效应研究
2.
Molecular dynamic study on size dependent melting temperature of Pb nanofilms;
铅纳米薄膜熔化温度尺寸效应的分子动力学研究
3.
Influence of interaction among agglomerative flux components on melting temperature of flux;
焊剂组元间交互作用对熔化温度的影响
6)  melting point
熔化温度
1.
Free energy method and the melting point of aluminum under the zero pressure;
自由能方法与零压下Al的熔化温度
2.
The effects of Li2O,NaF,Al2O3 and ZnO on soften and melting point of glass frits was studied.
研究了Li2O,NaF,Al2O3和ZnO对玻璃体系软化温度和熔化温度的影响,在此基础上研制出了软化温度Tg低于500℃、熔化温度Tm低于560℃的低温无铅玻璃。
3.
The influences of copper on properties of Zn-Al solders for Al/Cu brazing,which include wettability,shear strength of joint,microstructure of weld and melting point were studied.
研究了Cu元素对铝/铜钎焊用Zn-Al钎料的熔化温度、铺展性、接头剪切强度及焊缝组织的影响。
补充资料:初轧温度规程


初轧温度规程
temperature schedule of blooming mill

ehuzha wendu guieheng初轧温度规程(temperature seheduze ofblooming mill)在初轧机上将钢锭轧成钠坯时的温度方案。包括加(均)热温度、出炉温度、开轧温度、终轧温度、剪切温度和冷却方式等。 钢锭的加热温度与钢种有关。钢锭因含碳量(及含合金量)不同,加热上限温度不同,加热速度也不同。通常按含碳量把钢锭分成三组,分别规定它们的加(均)热温度即最高控制炉温和出炉温度. 第一组:含碳量C(。.3%的低碳钢,最高控制沪温为1380℃,出炉锭温为 1180一1220℃;第二组;含碳量。.3%。.6%的高碳钢和中碳合金钢,最高控制沪温1320,C,出炉锭温为1100一1150℃。 钢锭从均热炉运送到初轧机轧制还要降温30~50℃。钢锭开轧温度一般应在110。‘C以上,否则应重新加热,各均热炉坑最后三块钢锭的开轧温度允许稍微降低约30℃。终轧温度应在105。℃左右,不低于100。℃,决定于钢锭及钢坯的断面大小及轧制道次,断面大温度高,道次多温度低。钢坯的剪切温度在1000~800℃之间,应不低于800‘C。剪完后的钢坯根据不同要求采用冷却方式:第一组钢可进行空冷或水冷;第二组钢可进行空冷;第三组钢一般应进行缓冷及其他热处理。硅钢应直接热送至下一工序热装加热后继续轧制成成品。 (唐伟林)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条