1) model road surface
路面物理模型
1.
The ring capacitance is used to measure the thickness of model road surface.
分析了电容检测技术在公路路面厚度检测中的应用,利用环形电容传感器分别对自制的厚度不等的公路路面物理模型的厚度值进行检测,设计了以单片机为微处理器,兼有键盘、显示器、存储器等外围电路的电容测量电路对环形电容传感器的输出电容值进行采集,利用归一化处理方法依次得到不同厚度的路面模型的厚度值并显示出来。
2) two dimension model
平面物理模型
3) road model
路面模型
1.
A road model is provided in the time domain, and it is applied to analyse the dy-namic process of automobile braking.
建立了一种时域内的路面模型，并用于汽车制动过程的动态仿真分析中。
4) physical modeling
物理模型
1.
There- fore,the effect of lateral velocity alternation on structural imaging was discussed by using physical modeling technology.
利用物理模型建立了与实际情况较为符合的深度域层速度模型,对物理模拟数据进行了深度偏移处理,在深度偏移剖面上,原始地层和构造的几何形态基本得到了恢复。
2.
Coupling physical modeling and numerical analysis on pipe jacking behavior are performed.
以物理模型試驗及三維數值分析進行管推進工程研究,試驗方面以管推進物理模型試驗機模擬開挖面支撐壓力過大或不足對地表穩定性的影響,並於推進過程監測地表變位及土壓力變化;數值方面先以有限元素法程式ABAQUS模擬物理模型試驗之行為,將數值分析與模型試驗結果相互驗證,以檢討數值分析依據之Leca(1990年)淺屑隧道開挖面穩定理論及土壤組成律ExtendedDrucker-PragerModels。
3.
On the basis of physical modeling, the impact of different alignments on tidal factors such as tidal stage, tidal current velocity and tidal volume under the combined action of different runoffs and tides is studied, and the problem which causes the change of these tidal factors is analyzed.
通过物理模型试验 ,研究了黄茅海内不同治导线对潮汐要素的影响 ,得出治导线对河口湾内的潮位变化随着上游径流量的增加而逐渐减弱的结论。
5) physical model
物理模型
1.
Comparison of physical models of boiling heat transfer of porous surface tubes for heat exchangers;
换热器用多孔管沸腾传热物理模型比较
2.
Study on physical model of force during tube extrusion;
管材挤压力能参数物理模型
3.
A Study on a Physical Model of Moving Vehicle Weighing and Increase of Weighing Accuracy;
公路动态汽车称重物理模型与提高称重准确度研究
6) physics model
物理模型
1.
The research for the thermal drainage physics model test in the extension project of JiangSuchangshu electricity limited cooperation;
江苏常熟发电有限公司扩建工程温排水物理模型试验研究
2.
To establish the physics model of conductivity property in copper-clad and tinning copper-clad steel wire,give the way of calculating the basic parameter of them through design of plating technology and extract plating machine,meanwhile being checked by a set of test data,it shows that theory calculation results consist well with test results.
建立了铜包钢线及镀锡铜包钢线导电特性的物理模型，给出了电镀工艺和引镀机设计中计算铜包钢线及镀锡铜包钢线基本参数的方法，并用一组实验数据进行验算，结果证明理论计算和实验结果具有很好的一致性。
3.
This paper introduces the surface temperature distribution and temperature rising after taking out water from outlet through temperature difference flow test under typical hydrology condition,according to the design of cooling water physics model of the water supply and drainage project on phase 1,2 and 3 in Shanghai power plant.
本文主要根据冷却水物理模型试验关键相似条件,对于上海CJ电厂一、二、三期取排水工程冷却水物理模型进行了设计。
补充资料：泥沙物理模型
泥沙物理模型
sediment physical model
nlsha wull mox旧g泥沙物理模型(sediment physieal model) 见泥沙模型试脸。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条