1) shear compression test
剪压缩试验
1.
Under the high strain rate(102 s―1) condition,the shear compression failure of TC4 titanium alloy at different temperatures is researched using Fallwerk device and dynamic shear compression test method.
利用Fallwerk试验装置,在高应变率(102s-1)下,采用动态剪压缩试验研究TC4钛合金不同温度下的剪压缩失效现象。
2) pressure-shear test
压剪试验
1.
A series of pressure-shear test is carried out for lead laminated rubber bearing with small size(D<100mm).
对小型叠层橡胶支座（D＜100mm）进行了压剪试验研究，总结了这类支座的一些基本性能。
3) compression test
压缩试验
1.
A compression test and recrystallization simulation test of 41Cr4 steel(medium carbon and low alloy steel)had been performed by GLEEBLE 3500 subject to large strain and high temperature, then the volume fraction of recrystallization and true-stress and true -strain was obtained.
8)条件下,在Gleeble-3500试验机上进行了41Cr4钢的压缩试验和再结晶模拟试验,测得了再结晶体积百分数及真应力和真应变。
2.
In order to establish accurate constitutive equations for hot workings of metals, a large number of constant strain-rate compression tests have been done on thermal-mechanical testing machines (Gleeble-1500 and Formaster-press) using TC11 titanium alloy as testing materials.
为了建立本构方程，必须测量一定温度、应变速率范围内的流动应力值，这通常是由压缩试验来完成的。
4) compressive test
压缩试验
1.
The effects of Nb on the microstructure and properties of Ti50Ni42Al8 alloys are studied through compressive test,scanning electronic microscopy and X-ray diffraction measurements.
采用力学压缩试验、扫描电镜和X射线衍射方法研究了Nb元素对于Ti50Ni42Al8合金的力学性能和微观组织结构的影响。
5) load-shear test machine
压剪试验机
1.
Aiming at the non-linearity and parameter time-variation characteristics of the electro-hydraulic pressure system of the load-shear test machine,an interpolation algorithm fuzzy-PID controller is designed and developed on the basis of variable universe.
针对压剪试验机电液伺服压力系统的非线性和参数时变特性,研究设计了一种基于变论域插值模糊PID控制器。
2.
According to the non-linearity and variation against time of the electro-hydraulic pressure system of the load-shear test machine,an interpolation algorithm fuzzy-PID controller was designed and developed on the basis of variable universe.
针对压剪试验机电液伺服压力系统的非线性和特性时变性,研究设计了一种基于变论域插值模糊PID控制器。
6) hot compression test
热压缩试验
1.
Calibration of axisymmetric hot compression test results and verification for Cr9Mo steel
Cr9Mo钢热压缩试验结果的标定及验证
补充资料：压剪粘接强度
分子式：
CAS号：
性质：以压缩荷重对粘接面施加剪切应力，至粘接部位破坏的强度。多用于木材粘接力试验。
CAS号：
性质：以压缩荷重对粘接面施加剪切应力，至粘接部位破坏的强度。多用于木材粘接力试验。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条