1) height of residual oil column
残留油柱高度
1.
Based on the characteristics of residual hydrocarbons inside and outside the hydrocarbon kitchen and in combination with the relationship between buoyance of oil column in carrier beds and capillary pressure of pores,we determined the height of residual oil column and calculated the amount of residual oil in carrier beds.
以辽东湾凹陷为例,针对古近系沙河街组一、二段储层,通过地质统计方法及储层残留烃量与储层物性等数据的地质分析,根据油气在烃源灶内和灶外的残留特征,结合运载层油柱浮力与孔隙毛管压力的关系,确定残留油柱高度,并对运载层残留油量进行了计算。
2) Scallop height
残留高度
1.
According to the machining errors and scallop height required by the surface to be machined,we divide the discrete data point cloud which has been pro.
将散乱数据点云向XY平面投影,以获得的投影边界为刀具路径的主方向,然后根据曲面所需的加工误差和残留高度要求划分该投影数据点云,得到一系列刀位网格单元。
2.
The formula of scallop height,which can embody the curvature variety of the involute helicoid,has been dedu.
以大模数少齿数螺旋转子的渐开线螺旋面部分的加工为例,用球头铣刀在四轴立式加工中心上铣削渐开线螺旋面,计算残留高度时,运用此特性可求得能反映渐开线螺旋面曲率变化的残留高度计算公式。
3.
In view of the insufficiency of the tool path calculating in plunge tooling at the present day,a practical algorithm for calculating the step_length changeable plunge tool position based on scallop height restriction was put forward.
分析了插刀加工的特点 ,针对目前插刀加工刀具轨迹计算的不足 ,提出了1种实用的残留高度约束的变步长插刀加工刀位计算方法 ,并研究了插刀加工刀具轨迹中的分层处理、边界处理、刀具轨迹的优化生成方
3) milling remain height
残留高度
1.
Through resolving the intersection of scan surface,the milling remain height of ball end tool could be calculated.
残留高度是影响加工表面粗糙度的主要因素 ,本文在分析铣削加工过程中刀具刀刃实际扫成面的基础上 ,建立了实际刀刃扫成面的方程。
4) high residue level
高残留度
5) constant scallop height
等残留高度
1.
A flat-end cutter was used, its paths were generated based on the constant scallop height principle and machining strips were enlarged by adjusting inclinati.
提出了一种四坐标联动等残留高度端铣加工任意曲面叶片的方法。
2.
To obtain the parts surfaces’ constant scallop height after machining, a new toolpath generation algorithm named as curved surface mapping approach for 3D equidistant path-interval and conto.
曲面映射法是依据加工后零件表面材料余量呈现“等残留高度”的要求,设计的一种生成空间等距环切加工刀具轨迹的新方法。
6) constant scallop-height
等残留高度
1.
Research on Constant Scallop-height Tool-path Planning Method in High Speed Milling;
高速铣削加工中等残留高度刀具轨迹规划方法研究
2.
Aiming at the problem of longer tool path length and non-uniform scallop-height in section method for triangular mesh surface machining,an improved section-based algorithm for constant scallop-height tool path generation is proposed.
针对截平面法规划的三角网格表面的刀轨长度较长、加工表面残留高度不均匀的问题,提出一种基于改进截平面法的等残留高度刀轨生成算法。
3.
A tool path planning method of constant scallop-height based on Catmull-Clark subdivision surface was proposed.
提出了一种基于细分曲面等距面变形的逼近等残留高度刀轨生成算法。
补充资料：C15-20-α-烯烃与猪油、植物油残留物和硫酸化植物油残留物甲基混合酯的聚合物
CAS：83488-05-5
中文名称：C15-20 -α-烯烃与猪油、植物油残留物和硫酸化植物油残留物甲基混合酯的聚合物
C15-20-α-烯烃与猪油、植物油残留物和硫酸化植物油残留物甲基混合酯的聚合物
英文名称：
中文名称：C15-20 -α-烯烃与猪油、植物油残留物和硫酸化植物油残留物甲基混合酯的聚合物
C15-20-α-烯烃与猪油、植物油残留物和硫酸化植物油残留物甲基混合酯的聚合物
英文名称：
Alkenes, C15-20 .alpha.-, mixed with lard oil, vegetable oil residues and vegetable oil residues Me esters, sulfurized, polymd.
alkenes, c15-20 alpha-, mixed with lard oil, vegetable oil residues and vegetab； le oil residues me esters, sulfurized, polymd.
alkenes, c15-20 alpha-, mixed with lard oil, vegetableoil residues and vegetable oil residues me esters, sulfurized, polymd.
Alkenes,C15-20 .alpha.-,mixed with lard oil,vegetable oil residues and vegetable oil residues Me esters,sulfurized,polymd.
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条