1) Exhaust system model
![点击朗读](/dictall/images/read.gif)
排气系统模型
2) crew rostering system model
![点击朗读](/dictall/images/read.gif)
排班系统模型
4) drainage model
![点击朗读](/dictall/images/read.gif)
排水系统模型
1.
Computer technology propelled the development and application of drainage model software, which becomes a necessary means in urban storm water management.
计算机技术的发展推动了排水系统模型软件的开发和应用。
5) exhaust system
![点击朗读](/dictall/images/read.gif)
排气系统
1.
Simulation and optimization for vehicle exhaust system of vibration performance;
![点击朗读](/dictall/images/read.gif)
某轿车排气系统振动特性仿真及优化
2.
Numerical simulation of infrared radiation characteristics for exhaust system of an UAV with engine installed on the back of the fuselage;
发动机背负式安装无人机的排气系统红外特征的计算研究
3.
Numerical evaluation on infrared radiant intensity of exhaust system of turbine engine without afterburning;
非加力涡轮发动机排气系统红外辐射强度的数值计算
6) exhaust gas system
![点击朗读](/dictall/images/read.gif)
排气系统
1.
Regarding the 120,000DWT"TiaoJianHai" bulk carrier which has been transformed into the selfpropulsion loadreducing platform, a research on calculation of the exhaust gas system resistance for the power station engine and a quantitative analysis been conducted so as to discuss the probability of the design plan.
12万吨级"桃江海"号散装货轮改装为自航减载平台,对电站发动机排气系统阻力进行计算和定量分析,以探讨设计方案的可行性。
2.
Regarding the 120, 000DWT "TaoJianHai" Bulk carrier which has been transformed into the self-propulsion load-reducing platform, a research on the calculation of the exhaust gas system resistance for the power station engine and a quantitative analysis have been conducted so as to discuss the feasibility of the design plan.
12万吨级桃江海号散装货轮改装为自航减载平台,对电站发动机排气系统阻力进行计算研究,作定量分析,以探讨设计方案的可行性。
补充资料:排气
分子式:
CAS号:
性质:又称排气。在模塑初期阶段,使塑料所含水分或挥发分、空气或(和)熟化时所产生的水分及其他低分子挥发物质放出的操作。在热固性树脂模塑料的压塑成型中,压塑加热初期阶段,借助于瞬时开模以使空气或其他挥发分放出的操作。在传递模塑或注射成型中,系统借助于模腔内设置的小孔,或挤塑成型中借助于挤出机料筒所设的排气段放出水分、空气及其他挥发性物质。特别是制造大型制件或厚壁制品时,如不放气,则挥发性物质就会包封在制品内,经制品从模内取出后,制品表面会出现气泡、混浊或裂纹,使制品质量低劣。
CAS号:
性质:又称排气。在模塑初期阶段,使塑料所含水分或挥发分、空气或(和)熟化时所产生的水分及其他低分子挥发物质放出的操作。在热固性树脂模塑料的压塑成型中,压塑加热初期阶段,借助于瞬时开模以使空气或其他挥发分放出的操作。在传递模塑或注射成型中,系统借助于模腔内设置的小孔,或挤塑成型中借助于挤出机料筒所设的排气段放出水分、空气及其他挥发性物质。特别是制造大型制件或厚壁制品时,如不放气,则挥发性物质就会包封在制品内,经制品从模内取出后,制品表面会出现气泡、混浊或裂纹,使制品质量低劣。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条