1) resin impregnation-carbonization
树脂浸渍炭化
1.
0 g/cm~3 can be further dendified by resin impregnation-carbonization more times.
0 g/cm~3后,进行树脂浸渍炭化增密。
2) impregnated resin
浸渍树脂
1.
The characteristics of five different phosphinic(phosphoric)impregnated resins adsorbing heavy rare earth elements in hydrochloric acid are studied by static method.
利用静态法研究了5种不同膦(磷)类萃取剂的浸渍树脂在盐酸介质中对重稀土的吸附行为。
2.
The adsorption and elution of thulium,ytterbium and lutetium rich material were studied by cooperative extraction chromatography with Cyanex272-P507 impregnated resin,including the influence of concentrations of stripping agents,the load of Tm-Yb-Lu rich material,effluent velocity and temperature on eluting Tm-Yb-Lu.
以Cyanex272-P507浸渍树脂采用萃取色层法对铥镱镥富集物进行了吸附和淋洗分离研究,考察了淋洗剂浓度、稀土负载量、淋洗液流速等因素对分离铥镱镥富集物的影响。
3.
The TPPS4 impregnated resin was prepared by loading meso-tetra-(4-sulfophenyl)porphine (TPPS4) onto a macro-porous adsorption resin 1300-Ⅱ.
本文用ｍｅｓｏ－四（４－碳酸苯基）卟啉处理１３００－Ⅱ型大孔吸附树脂制得县有相应卟啉基团的浸渍树脂（ＴＰＰＳ４浸渍树脂），并用静态法求得ＴＰＰＳ４浸渍树脂吸附镉的最佳ｐＨ，平衡速率、吸附容量、吸附物组成及热力学函数等。
3) Resin impregnation
树脂浸渍
1.
Resin impregnation was used to densify carbon fiber preforms after they had been densified by chemical vapor deposition (CVD).
将炭纤维坯体CVD增密至不同密度,再对其进行树脂浸渍。
2.
85g/cm 3 by resin impregnation after pre-densification to different initial densities by CVD(chemical vapour deposition).
将CVD预增密至不同初始密度的C/C复合材料进行树脂浸渍 /炭化补充增密至 1 85 g/cm3,热处理后进行热物理性能的检测和不同刹车压力的摩擦磨损试验。
4) impregnating resin
浸渍树脂
1.
Vacuum foaming behaviour and test method of foaming vacuity of an impregnating resin;
浸渍树脂的真空沫化特性及其沫化真空度试验方法
2.
Research progress of impregnating resin used in automobile filter paper;
汽车滤纸浸渍树脂研究进展
3.
The compositing route,manufacturing process,routine performances and ageing tests of H9110unsaturated polyester-imide impregnating resin are introduced.
通过优化分子结构和封端技术制备了H9110不饱和聚酯亚胺无溶剂浸渍树脂 ,研究了合成路线、制造工艺、常规性能和老化试验 ,并将其与国内外同类产品进行综合比较 ;结果表明 ,该浸渍树脂低温快固化、成本较低、性能良好 ,能够满足高压电机少胶云母带配套VPI绝缘结构的性能及工艺要求。
5) impregnating-carbonization
浸渍-炭化
1.
This paper studied processing parameters of 2D-carbon/carbon composite laminates by impregnating-carbonization route,and analyzed the effect of different precursors and densification times on density,thickness and shrinkage,volume resistance and interlaminar shear strength(ILSS);and fracture morphology was further analyzed by SEM.
研究通过浸渍-炭化法制备二维C/C复合材料层叠板的工艺参数,分析了不同基体前驱体和增密次数对材料的密度、厚度和收缩率、体积电阻率和层间剪切强度的影响,并用扫描电子显微镜进行断口分析。
6) Cyanex272 impregnated resin
Cyanex272浸渍树脂
1.
The influence of separating thulium-ytterbium-lutetium-rich material and parameter of chromatography column were studied by extraction chromatography with Cyanex272 impregnated resin,including temperature,column rations,the acid concentrations in eluting,loading of rare earths and flow rates.
研究了不同温度、淋洗液酸度、稀土负载量、淋洗液流速及装柱树脂高度对Cyanex272浸渍树脂萃取色层法分离Tm,Yb,Lu的影响和柱参数。
补充资料：树脂
分子式：
CAS号：
性质：相对分子量不确定但通常较高，常温下呈固态、中固态、假固态，有时也可以是液态的有机物质。具有软化或熔融温度范围，在外力作用下有流动倾向，破裂时常呈贝壳状。广义上是指用作塑料基材的聚合物或预聚物。一般不溶于水，能溶于有机溶剂。按来源可分为天然树脂和合成树脂；按其加工行为不同的特点又有热塑性树脂和热固性树脂之分。
CAS号：
性质：相对分子量不确定但通常较高，常温下呈固态、中固态、假固态，有时也可以是液态的有机物质。具有软化或熔融温度范围，在外力作用下有流动倾向，破裂时常呈贝壳状。广义上是指用作塑料基材的聚合物或预聚物。一般不溶于水，能溶于有机溶剂。按来源可分为天然树脂和合成树脂；按其加工行为不同的特点又有热塑性树脂和热固性树脂之分。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条