1) microlayered coextrusion
微层共挤出
1.
Two barrier materials,HDPE/PA6 and PP/(EVOH+PP),were prepared by the microlayered coextrusion device designed in our laboratory.
利用实验室自行设计制造的微层共挤出装置制备了2种交替层状高分子阻隔材料,即HDPE/PA6和PP/(EVOH+PP)。
2.
Microlayered conductive carbon black filled polypropylene/polypropylene(PPCB/PP) composites were prepared via the microlayered coextrusion system designed in our lab.
利用自主设计的微层共挤出设备,制备了具有交替微层结构的炭黑填充聚丙烯/聚丙烯(PPCB/PP)导电复合材料。
2) microlayered extrusion
微层挤出
1.
In order to optimize the dispersion of the multiwalled carbon nanotubes(WMNTs) filled polymer composites,Microlayered WMNTs filled polypropylene composites were prepared via the microlayered extrusion system designed in our lab.
DSC证明,WM-NTs具有很强的异相成核作用,微层挤出样品的结晶尺寸分布比1层样品更宽。
3) double coextrusion head
双层共挤出机头
4) co-extrusion
双金属挤压、多层一次挤出、共挤出(法)
5) co-extrusion
共挤出
1.
The development and characteristic of plastic co-extrusion for blow heavy packing complex membrane unit;
塑料共挤出吹塑重包装复合膜机组的研发及特点
2.
The application of co-extrusion technology in the process of polymer molding such as composite pipe, composite membrane, profile, panel, wire, cable and optical fiber was summarized.
综述共挤出技术在聚合物成型加工中的主要应用,包括复合管材、复合薄膜、异型材、板材、电线、电缆、光纤等的复合共挤出。
6) coextrusion
[,kəueks'tru:ʒən]
共挤出
1.
The three-dimensional flow of non-Newtonian polymer melts (LPDE/PS) in coextrusion dies was analyzed based on finite element simulations.
采用有限元方法对两种聚合物熔体(LDPE/PS)在共挤出流道内的流动进行了三维数值模拟,分析了两种熔体的入口体积流量比、熔体与模具壁面之间的滑移系数等物理量对于共挤出界面位置和形状的影响。
2.
The die swell phenomena of isothermal non-Newtonian polymeric fluids in coextrusion processes were simulated by means of the finite element method.
采用有限元方法模拟了非牛顿流体在共挤出过程中的挤出胀大现象,分析了模具流道收敛角、模具内壁的表面质量以及平直段长度对共挤出聚合物挤出胀大的影响。
3.
A finite element method was used to simulate the two-dimensional isothermal non-Newtonian polymeric fluid flow in coextrusion dies.
以HDPE/LDPE共挤出型材为例,用有限元方法对非牛顿流体在共挤出流道内的等温流动进行了二维数值模拟。
补充资料：复合机头挤出
分子式：
CAS号：
性质：轮胎胎面胶两种胶料整体挤出成型的专用工艺。即一个复合挤出机头与两台挤出机相连接，两台挤出机的两种胶料通过复合机头同时挤出形成整体胎面胶的方法。两种胶料分别为胎冠胶和胎侧胶，以满足轮胎胎面不同部位使用不同性能胶料的需要。
CAS号：
性质：轮胎胎面胶两种胶料整体挤出成型的专用工艺。即一个复合挤出机头与两台挤出机相连接，两台挤出机的两种胶料通过复合机头同时挤出形成整体胎面胶的方法。两种胶料分别为胎冠胶和胎侧胶，以满足轮胎胎面不同部位使用不同性能胶料的需要。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条