1) cold and hot wire
冷丝和热丝
1.
The various high efficiency submerged arc welding methods was introduced,including multiple wires submerged arc welding,band electrode submerged arc welding,submerged arc welding with alloyed metal powders,narrow gap submerged arc welding,cold and hot wire filled submerged arc welding.
介绍了多丝埋弧焊、带极埋弧焊、添加合金粉末埋弧焊、窄间隙埋弧焊、冷丝和热丝填丝埋弧焊等多种高效埋弧焊方法,并就各自的工艺特点、国内的应用情况进行了分析与总结。
2) cool and thermal-channel spinning
冷管热管纺丝
1.
Various ways of spinning Ⅱ.The spinning tension in cool and thermal-channel spinning and the process adjustment;
花色纺丝II.冷管热管纺丝张力不匀及工艺调节
3) arc-assisted hot-wire welding of cool-body
热丝冷体TIG堆焊
1.
Wetting and spreading in arc-assisted hot-wire welding of cool-body with wire HS201;
热丝冷体TIG堆焊中的HS201焊丝润湿铺展研究
4) hot wire
热丝
1.
Submerged Arc Welding(SAW) with hot wire addition is a new welding technology developed from tranditional SAW with high quality,high efficiency and low energy consumption.
热丝填充埋弧焊是在传统埋弧焊基础上发展起来的一种优质、高效、节能的焊接新工艺。
2.
This paper focuses on the fabrication of the film by the method of hot wire assistance chemical vapor deposition.
本文主要研究了热丝辅助裂解电阻蒸发法制备该薄膜的制备工艺 ,并采用红外、质谱和热重等分析方法对薄膜的成分进行初步分析。
3.
In addition, problems of incomplete fusion and narrow girdling are solved in the case of combining interbedded heat preservation and hot wire technology.
通过对比单,双光束填丝焊的焊缝成形特征,确定气孔、未熔合为高强钢厚板激光多层焊的主要缺陷,双光束可有效提高焊接稳定性、降低焊缝气孔,同时明显提高焊丝对中性能;辅助层间保温与热丝技术可有效解决末熔俣与层间束腰过小问题。
5) hot-wire
[英]['hɔt,waɪə] [美]['hɑt,waɪr]
热丝
1.
Computer controlling hot-wire GTA all-position tube welding system;
微机控制热丝GTA全位置焊管系统
2.
A kind of atomic beam intensity detector,hot-wire detector,is designed and made by the authors.
一种自行研制的原子来信号专用测量仪器，即原子束热丝探测仪。
6) filament
[英]['fɪləmənt] [美]['fɪləmənt]
热丝
1.
In the paper , the method of analyzing the failed mechanisms of short filament and turnoff in high - power wideband TWT is introduced.
对宽频带大功率行波管热丝短、断路失效机理进行了分析,并在机理分析的基础上,讨论消除这一失效模式而采取的措施及其效果。
补充资料：筒管纺丝
分子式：
分子量：
CAS号：
性质：制造人造丝的一种纺丝方法。由凝固浴出来的已经成形的丝条，经过不断往复运动的导丝钩，交叉卷绕在转动的筒管上。与离心纺丝不同，所得丝条无拈度，需要时再进行加拈。筒管上一般有许多直径约2毫米的小孔，主要是为了便于压洗除去纤维中的少量杂质。
分子量：
CAS号：
性质：制造人造丝的一种纺丝方法。由凝固浴出来的已经成形的丝条，经过不断往复运动的导丝钩，交叉卷绕在转动的筒管上。与离心纺丝不同，所得丝条无拈度，需要时再进行加拈。筒管上一般有许多直径约2毫米的小孔，主要是为了便于压洗除去纤维中的少量杂质。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条