1) internal plane bulkhead
内部平面舱壁
1.
In this paper,we analyse the design status for the internal plane bulkhead of the domestic submarine,add and improve the bending moment and shear force formula of the level crossbeam and the vertical beam on the beam bracket.
对国内潜艇内部平面舱壁的设计现状进行了分析研究,补充与完善了水平大梁与垂直梁肘板处的弯矩与剪力的公式。
2) internal domed bulkhead
内部球面舱壁
1.
Variant kinds of reinforced structure in connecting place of internal domed bulkhead and pressure hull have a very large effect on the stress on pressure hull.
耐压壳体内部球面舱壁与耐压壳体连接处加强结构的不同 ,对该处耐压壳板受力影响很大。
3) plane bulkhead
平面舱壁
1.
Model test research on ultimate strength of plane bulkhead supported by inside deck of submarine;
平台支撑的潜艇内部平面舱壁极限强度的模型试验研究
2.
Using general nonlinear finite element analysis program,ultimate strength analysis on plane bulkhead supported by inside deck of submarine is performed in this paper.
借助国际通用的大型非线性有限元分析软件,对潜艇内部以加强平台取代水平横桁的平面舱壁结构的极限强度进行了非线性的有限元分析。
3.
In order to examine the type of plane bulkhead which takes the deck instead of the horizontal girder as its primary support,and to study the supporting effect of deck on the bulkhead,two section models with different deck structures were designed and manufactured.
为了研究平台对舱壁的支撑作用,针对以内部平台取代水平桁作为一级支持构件的潜艇平面舱壁结构形式,设计制作了两个平台强度不一样的舱段模型。
4) end plane transverse bulkhead
端部耐压平面舱壁
5) plane hatch wallboard
平面舱壁板
1.
On the basis of analysis for submarine plane hatch wallboard external pressure condition,indicate external load of submarine plane hatch wallboard stability verify should not less than submarine pressure hull calculating loa
本文在分析潜艇耐压艇体内部平面舱壁板受力情况的基础上 ,提出平面舱壁板稳定性校核中外载荷应取不低于潜艇耐压艇体的计算载荷P
6) plane transverse bulkhead
平面横舱壁
补充资料：内部
内部
interior
囚都t加挽幻份;皿yT那二ocT‘J 拓扑空间X的子集A的满足下列条件的所有点x的集合:存在X中的开集U:，使x任U:CA.集合A的内部通常记为IntA，且表示含于A内的X中的最大开集.等式IntA=x\「X\A」成立，这里〔X}表示X的闭包.拓扑空间X中集合的内部是正则开(化孚血r open)集或典范集(。口训jCalset).其典范开集构成拓扑基(b朋e)的空间称为半正则的(~一记gu~lar).所有正则空间都是半正则的.内部有时也称为集合的开核(open ken祀1 of the set). B .H，floH咖apeB撰【补注1亦见集合的内部(泊忱由r of a set). 白苏华、胡师度译
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条