1) parallel temperature
温度对口
1.
A power and heat cogeneration system with three biogas digester at different temperature,namely thermophilic,mesophilic,and ambient temperature was designed according to a principle of "parallel temperature and gradient energy utilization".
基于"温度对口,能量梯级利用"的原则,设计了新型的三级恒温沼气热电联供系统。
2) temperature window
温度窗口
1.
To study the influences of methane on selective non-catalytic reduction (SNCR), the condition of flue gas composition was simulated on a drop tube furnace test rig, and the influences of a few of methane on SNCR temperature window, NOx reduction efficiency and ammonia slip from 650℃ to 1 150 ℃ were investigated, as well as reactivity of methane.
为研究甲烷对选择性非催化还原(SNCR)脱硝反应的影响作用,在沉降炉实验台上模拟锅炉烟道内的反应环境和烟气成分,在650~1150℃范围内,研究了微量甲烷对SNCR反应温度窗口、脱硝效率和氨泄漏的影响,以及甲烷在脱硝过程中的反应特性。
2.
By using advanced commercial software CFX-TASCFLOW imported from abroad,a numerical simulation of said combined application on the W-shaped flame boilers of 300 MW unit in one power plant has been carried out,the key parameters suitable for temperature windows of SCNR being precisely calculated and analysed under different optimized combustion modes.
用国外先进商业软件CFX-TASCFLOW对某电厂300 MW机组W火焰锅炉采用低NOx燃烧与SNCR技术联合应用进行了数值模拟,重点对不同优化燃烧模式下适合于SNCR温度窗口的关键技术参数进行了准确的计算分析。
3) Inlet Temperature
入口温度
1.
Three-dimensional Finite Element Model (FEM) Analysis of the Roller's Shape with an Uneven Inlet Temperature Field in Continuous Roll-casting Process;
非均匀入口温度场下铸轧辊辊型的三维有限元仿真
2.
Propellant inlet temperature control for cryogenic rocket engine tests
低温发动机试验推进剂入口温度控制
3.
The influence of fluid component content and inlet temperature on the flow in gas condensate pipeline-riser system
流体组分含量及入口温度对天然气凝析液输送管道立管系统流体流动特性的影响
4) inlet temperature
进口温度
1.
Experimental study of influence of inlet temperature on aviation kerosene coking characteristics
进口温度影响航空煤油结焦特性实验
2.
The influence of inlet temperature of cooling water on the solidification of paraffin outside the coil tube was investigated.
Anica等[1-2]通过实验和数值计算研究了壳管式换热器中传热流体和石蜡间的传热过程,对传热流体的流速和进口温度,以及传热管的长度和外径对石蜡温度场、储能/释能进行了数值分析。
5) Outlet temperature
出口温度
1.
The result shows that the outlet temperature by partial charged method is more steady and its discharging rate is higher than that by fully charged method.
比较了两种冻结方式在蓄冷和释冷过程中的传热性能,结果表明,不完全冻结方式在释冷过程中盘管出口温度更稳定、释冷速率更高,给出了不完全冻结必须满足的条件。
2.
On the basis of on-site data and in conjunction with the working principle of a power plant coal-pulverizer system a state-space dynamic mathematical model has been set up of the coal pulverizer outlet temperature and pulverizer inlet-air flow rate through an analysis of the coal pulverizer control system.
基于现场数据 ,结合电厂磨煤机系统的工作原理 ,通过对其控制系统分析 ,建立了磨煤机出口温度和磨煤机入口空气流量的状态空间动态数学模型。
3.
Two calculation methods for combustor outlet temperature of an aeroengine were described.
概要介绍了某型航空发动机燃烧室出口温度的2种计算方法,结合发动机试车数据对采用2种计算方法得到的结果进行了对比分析。
6) wound temperature
切口温度
1.
Purpose:To comparatively study the wound temperature in bimanual microphacoem-ulsification and conventional phacoemulsification.
目的:研究白星系统在双手微切口超声乳化术中对切口温度的影响,在切口安全性方面与常规术式进行对比。
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条