1) migration e
偏移量e
1.
It is needed to be tested in the operating process that include the migration e between survey line and centre point of pipe,the height H from centre point in pipe hole to slide ring of triangulation frame and the depth H0 comes from the circular ball in the pipe hole.
现场操作中只需测量测线与管桩中心点的偏移量e,管桩孔口中心到三脚架滑环的高度H以及环型圆球在管桩管内的深度H0,通过这三个参数就可以计算管桩的倾斜角和垂直度。
2) eccentricity in stitches
偏心量e
1.
In this paper, the relationship between eccentricity in stitches and structure properties of sewing threads is studied by means of multiple linear stepwise regression and the following result is obtained: eccentricity in stitches is most related to bending rigidity, linear density and friction coefficient of sewing threads.
本文运用相关分析和多元逐步回归分析对缝纫线迹的偏心量e和缝纫线的结构性能之间的关系进行 了研究,发现偏心量e与缝纫线的弯曲刚度、线密度和摩擦系数的关系最密切。
3) State of E polarization
E矢量偏振状态
4) offset
[英]['ɔfset] [美]['ɔf'sɛt]
偏移量
1.
Analysis and calculation for electrode-wire offset in wedm programming;
线切割编程中电极丝偏移量的分析与计算
2.
Influence of the injection pressure to plastic mould core offset;
注射压力对塑料模具型芯偏移量的影响
3.
On the setting of longitudinal offset of continuous beam bridge;
连续梁桥纵向偏移量设置
5) deviation
[英][,di:vi'eɪʃn] [美]['divɪ'eʃən]
偏移量
1.
Producing causation and check method of nucleon density instrument deviation;
核子密度仪偏移量的产生原因及校核方法
2.
In order to modify the calculation,the center datum is established for deviation calculation on the basis of characteristics of quality changes so as to ensure the capacity index could reflect the quality of products correctly.
确立中心数,探讨计算偏移量的方法,决定偏移程度,弥补过程能力指数计算公式的缺陷,以便使过程能力指数准确地综合反映单控产品质量的状况及过程的质量保证程度。
3.
This article mainly deals with the way to control the thickness of the coating with a photo electric sensor instead of the expensive β-ray gage,the way to control the deviation of rnargin with a photoelectric ruler and the way to control the length of the plaster with an infrared sensor.
涂膏机是医用卫生材料行业生产医用膏布（如麝香关节止痛膏）中的关键设备，本文重点介绍了采用光电传感器代替昂贵的β射线测厚仪，对其实现涂层厚度（即含膏量）控制；采用研制开发的数字量输出的光尺传感器实现布边偏移量控制；采用红外光电传感器实现膏布长度计量控制。
6) displacement
[英][dɪs'pleɪsmənt] [美][dɪs'plesmənt]
偏移量
1.
When language program of a single-chip microcomputer is assembled manually,the calculation of displacement will be very hard This paper puts forward a program used in calculating the displacement to replace manual wor
单片机汇编语言程序用手工汇编时，偏移量的计算工作量很大。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条