说明：双击或选中下面任意单词，将显示该词的音标、读音、翻译等；选中中文或多个词，将显示翻译。
您的位置：首页 -> 词典 -> 内焊缝磨削机
1)  inside weld grinding machine
内焊缝磨削机
1.
Aiming at the former expanded device of inside weld grinding machine was too complex in structure and the diameter of grinding disc was on the small side,which caused the residual weld reinforcement failed to meet the requirement of standard after grinding.
针对原有内焊缝磨削机胀紧机构过于复杂,磨削轮直径偏小易造成磨削后的焊缝残余高度不符合标准要求,以及磨削时经常会磨损磨削轮侧面等问题,对设备进行了较大的改造。
更多例句>>
2)  Welding seam grinding
焊缝磨削
例句>>
3)  flush weld/ weld machined flush
削平焊缝
4)  weld grinding
焊缝打磨
5)  inner raceway grinding
内沟磨削
1.
With the modification of 8861A and the improvement of inner raceway grinding of spherical roller bearings.
通过对老设备M8861A的改装和重新安排调心滚子轴承内沟磨削工序,使原磨削该类型轴承内沟的关键设备提高了生产效率,降低了消耗。
6)  cutting tool manuiacture
磨削内孔
补充资料：ANSYS工字梁焊缝初应力例子

建立好模型
…..
/SOLU
!*
ANTYPE,0
/INPUT,'input','txt',
/INPUT,'output1','txt',
!*
ISFILE,READ,1,txt, ,0
SOLVE
=====================
!定义残余应力矩阵
I=1
fy=310e6
!定义单元中心坐标数组，初应力数组
*DIM,EleCenter,ARRAY,NumNode,3,1, , ,
*DIM,EleIS,ARRAY,NumNode,1,1, , ,
*DO,I, 1, NumNode,1
!得到单元中心坐标
*GET,EleCenter(I,1,1),ELEM,I,CENT,X
*GET,EleCenter(I,2,1),ELEM,I,CENT,Y
*GET,EleCenter(I,3,1),ELEM,I,CENT,Z
!焊缝位置在X=1.0 到1.05 之间
*IF,EleCenter(I,1,1),GT,1,THEN
*IF,EleCenter(I,1,1),LT,1.05,THEN
*IF,EleCenter(I,2,1),GT,0.5,THEN
!上翼缘初始应力
EleIS(I,1,1)=-20*fy*EleCenter(I,3,1)**2+0.3*fy
*endif
*IF,EleCenter(I,2,1),LT,0.0,THEN
!下翼缘初始应力
EleIS(I,1,1)=-20*fy*EleCenter(I,3,1)**2+0.3*fy
*endif
!腹板初始应力
*if,EleCenter(I,2,1),GE,0.0,THEN
*IF,ELECENTER(I,2,1),LE,0.5,THEN
EleIS(I,1,1)=4.076*fy*(EleCenter(I,2,1)-0.5)**2
EleIS(I,1,1)=EleIS(I,1,1)-0.719*fy
*IF,EleIS(I,1,1),LT,-0.3*fy,THEN
ELeIS(I,1,1)=-0.3*fy
*ENDIF


*ENDIF
*ENDIF
*ENDIF
*ENDIF
*ENDDO
===============
!输出应力数值
*CFOPEN,'1','txt',' '
*DO,I,1,3840
!*IF,EleIS(I,1,1),ne,0.,then
*VWRITE,'!'
(A)
*VWRITE,'! Stress for element',
(A,F)
*VWRITE,'!'
(A)
*VWRITE,'eis,',I
(A,F)
P=EleIS(I,1,1)
*VWRITE,P,0.,0.,0.,0.,0.
(E,E,E,E,E,E)
!*ENDIF
*ENDDO
*CFCLOS

说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条