1) blade of scrap shear
碎边剪剪刃
2) blade rolling
切边剪刃
1.
Trimming the quality of the blade rolling acid (acid wash) board passing rates,Yield, yield and the cost is extremely important implications,Although imports blade stable quality,but supplies are long cycle,prices high,do a good job the introduction of the technical transformation of the drawings is necessary.
切边剪刃的质量对酸连轧(酸洗)板的合格率、成材率、产量和成本有着极其重要的影响,虽然进口剪刃质量稳定,但供货周期长,价格高,因此做好引进图纸的技术转化工作非常必要。
3) Scrap chopper
碎边剪
1.
Causes analysis of shearing defects of scrap chopper and its countermeasures;
碎边剪剪切缺陷的产生原因及改进
2.
To solve the cutter frequent changing, the guide box of scrap chopper was improved in cold rolling mill of Echeng Iron and Steel Co.
鄂城钢铁集团公司冷轧分厂为了解决宽带钢碎边剪刀具更换频繁问题 ,对碎边导卫盒装置进行了改进 ,换刀具周期由 10天一次改为 2～ 3个月一
4) flying shear cutter
飞剪式碎边剪
5) blade
[英][bleɪd] [美][bled]
剪刃
1.
The blades of hot shear made of 4Cr2WMoVSi steel was tested in production.
以多元少量的合金化原则设计的4Cr2WMoVSi钢是一种经济型热作模具钢,研究了4Cr2WMoVSi钢的热处理工艺及性能,并与3Cr2W8V钢的热处理工艺和性能作了对比,用4Cr2WMoVSi钢制作了热剪刃,进行了装机使用试验,其使用寿命与3Cr2W8V剪刃的寿命相当,而是5CrW2Si剪刃寿命的3。
2.
The blade clearance plays an important role in the quality and precision adjustment in shearing area.
滚筒机构飞剪机是高速连轧机组中的关键设备,其剪刃侧隙对剪切断面的质量、调节精度起着重要的作用。
3.
According to management of side trimmer and blade,the quality of cold strip trimming cut has been effectively improved.
针对冷轧生产中出现的板带切边的断面缺陷,研究各种缺陷产生的机理,给出切边断面缺陷产生的种种原因以及表现形式,与轧制后边部缺陷的对应关系,通过对切边剪和剪刃的管理以及剪刃间隙的调节,使冷轧板带切边质量得到有效的提高。
6) shear blade
剪刃
1.
This paper introduces the figure of the hydraulic shearer and the working principle of the hydraulic control system,detailedly analyses the design and calculation of parameter of shearing force,compaction force,stroke of shear blade and hydraulic cylinder for shearer and verifies by the calculation process of design example.
介绍了液压横剪机的外形结构及液压控制系统工作原理,并对横剪机的剪切力、压紧力、剪刃行程、液压缸选型等参数的设计、计算作了详细分析,并通过设计实例的计算过程加以验证。
2.
The comprehensive mechanical properties of 6CrW2Si steel shear blade were demanded according to its failure forms and service conditions.
在对６ＣｒＷ２Ｓｉ钢剪刃失效方式和服役条件分析的基础上，提出了剪刃的综合力学性能要求。
补充资料：宝山钢铁(集团)公司热轧带钢厂精轧机组前的切头飞剪
宝山钢铁(集团)公司热轧带钢厂精轧机组前的切头飞剪
触二赚庶‘阿月;1一心三三二如崛之，‘叮登呱;~~，二.尸日口」.嗓二热巍 宝山钢铁(集团)公司热轧带钢厂 精轧机组前的切头飞剪
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条