1) Electromechanical Integrative Simulation
机电联合仿真
2) co-simulation
联合仿真
1.
Research on Co-simulation Using ADAMS and MATLAB for Vibration Isolation Station of Micro-manufacture;
微制造隔振平台的ADAMS和MATLAB联合仿真研究
2.
Co-simulation Study of Automobile Electronic Power Steering System Based on AMESim and Simulink;
基于AMESim和Simulink的汽车电动助力转向系统的联合仿真
3.
Dynamic Co-Simulation of NC machine tool based on machine joints modeling;
基于结合面建模的数控机床动力学联合仿真研究
3) joint simulation
联合仿真
1.
Study and application of joint simulation systems;
联合仿真反事故演习系统应用与研究
2.
Study and Realization of Joint Simulation Based on SystemView and Matlab;
SystemView与Matlab联合仿真的研究与实现
3.
Based on the joint simulation, the optimal firing interval of the two tubes is given to avoid the aerodynamic influence of the muzzle areas.
该文应用ADAMS和MATLAB两大软件平台,建立了某双管火炮的虚拟样机联合仿真模型,并进行了双管耦合发射动力学联合仿真。
4) combined simulation
联合仿真
1.
Combined Simulation of the Vehicle s Braking Performance Based on VC, Matlab;
基于VC、Matlab的汽车制动性能联合仿真
2.
The combined simulation research of vehicle steering and braking system;
车辆转向与制动系统联合仿真研究
3.
With that the combined simulation of vibration characteristics is carried out on the base of MATLAB/Simulink and ADAMS,in which the transmission effects and aero-.
采用叶素动量理论进行风力机气动力学的计算分析,并对风轮和塔架进行了有限元模态分析,建立风力机ADAMS柔性多体动力学仿真模型,并在MATLAB/Simulink环境下建立风力机传动链的数学模型,同时进行传动链系统的编程运算,充分考虑了气弹耦合特性以及传动系统的影响,最终实现在MATLAB/Simulink和ADAMS基础上对风力机系统振动性能的联合仿真。
5) United simulation
联合仿真
1.
United simulation technique with AMESim and Matlab/Simulink was discussed based on their own characteristics.
根据AMESim与Matlab/Simulink软件各自的特点,对两者联合仿真技术进行了研究,解决了联合仿真的接口与实现问题,并把该技术应用于电液位置伺服系统的传真,取得了良好的效果。
2.
Based on complexities of the dynamic model and trajactory tracking control of free-floating space manipulator,the dynamic model of free-floating space manipulator based on ADAMS,fuzzy control system of trajectory tracking and united simulation combined with ADAMS and Matlab are expressed.
针对空间机械臂动力学建模和轨迹跟踪控制的复杂性,详细介绍了在虚拟样机技术软件ADAMS里,建立漂浮基空间机械臂的动力学模型、轨迹跟踪模糊PD控制策略及其ADAMS和Mat-lab的联合仿真。
3.
In view of ADAMS could not realize complex controls of the mechanical system,this paper proposed the united simulation method by ADAMS and control system application software MATLAB.
针对ADAMS不能对机械系统实现复杂控制的状况,提出了将ADAMS与控制系统应用软件MATLAB结合起来对系统进行联合仿真的方法。
6) cosimulation
联合仿真
1.
Modeling of Mechatronic Systems: Cosimulation;
机电一体化系统的联合仿真技术研究
2.
The cosimulation model was realized with the conjunction of the above models and the ABS performance could be studied.
首先利用ADAMS软件,建立了某轿车的14自由度虚拟样机仿真模型;再在Matlab/Simulink环境下,建立ABS制动器及其控制模型;将虚拟样机模型与ABS的控制模型相结合,从而构成研究ABS性能的联合仿真模型。
补充资料：机电
机械和电力设备的统称：～产品。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条