说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 最小割集-网络等值法
1)  minimum-cutset & network-equivalent method
最小割集-网络等值法
2)  minimal cutting set algorithm
最小割集法
1.
Aimed at the background problems of complexity of network and of reliability of units,start from the angle of network tree to analyze the network system,the reliability estimation methods: minimal cutting set algorithm and minimal route set algorithm were synthetically and qualitatively analyzed at first,and the selection principle of reliability estimation method was advanced.
针对网络的复杂度和单元的可靠度等背景问题,从网络树的角度分析网络系统,首先综合定性分析可靠性估算方法:最小割集法和最小路集法,提出可靠性估算方法的选择原则;然后基于可靠性单元,建立了网络系统可靠性简化算法;最后运用该算法对某一输水泵站系统进行了可靠性计算。
3)  network-equivalent method
网络等值法
1.
The paper introduces the feature of distribution system reliability evaluation,and the methods used for reliability evaluation,such as failure mode and effect analysis(FMEA),minimum path / cut set method,network-equivalent method,fault-spreading method,Monte Carlo method as well as some artificial intelligence methods.
介绍了配电系统可靠性评估方法——故障模式与后果分析法(failure mode and effect analysis,FMEA)最小路-割集法、网络等值法、故障扩散法、蒙特卡罗模拟法以及一些人工智能算法,并对各种方法进行总结、分析和评价,为配电系统可靠性研究提供一些借鉴。
4)  m inimal cut set algorithm
最小割集算法
5)  minimum cut set
最小割集
1.
The system risk is analyzed based on the minimum cut sets which are solved using the Semanderes algorithm.
利用Semanderes算法求出故障树的最小割集,对客滚运输安全进行定性分析。
2.
The minimum cut sets(fault spectrums) are obtained by qualitative analysis.
通过定性分析,找出了抽油杆事故的全部最小割集—故障谱。
6)  minimum cut sets
最小割集
1.
Qualitative analysis and quantitative analysis are made by using of fault tree analysis,minimum cut sets and importance are calculated.
利用故障树分析法对系统进行定性分析和定量计算,求出系统的最小割集和重要度。
2.
All of minimum cut sets of fault trees are found out and the qualitative analysis .
求取了故障树的所有最小割集,并对该电子式电流互感器的可靠性进行了定性分析。
3.
Introduces a new simulation method based on the minimum cut sets of fault tree, analyzes the way using the method in the research of the reliability of FMS, a case is presented to prove its correctness.
介绍了基于最小割集的仿真方法的原理及其具体实现过程 ,并分析了它在柔性制造系统FMS(FlexibleMachingSystem)可靠性研究中的应用 ,最后用一个FMS的实例来验证该方法的正确性。
补充资料:最小辐亮度与最小辐照度(见核爆炸火球)


最小辐亮度与最小辐照度(见核爆炸火球)
minimum-brightness and minimum-irradiance

zuixiao fuliangdu yu zuixiaofu乙haodu最小辐亮度与最小辐照度(minimum-brightness and而nimum一irradianee)见核爆炸火球。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条