1) Synthesis Measurement
综合法测量
3) Synthetic measurement
综合测量
1.
In order to settle the traditional tool s problems of limited precision and applicability, the technique of tractor crankshaft synthetic measurement based on virtual instrument is introduced.
提出了基于虚拟仪表的曲轴综合测量技术 ,为解决以往传统曲轴检测工具精度不够、针对品种单一等缺点提供了依据。
2.
With the rapid development of manufacture technologies, the synthetic measurement of profile with large range and high precision has become more and more imminent.
随着制造技术的快速发展,对各种零件表面轮廓进行大量程、高精度的综合测量的需求也越发迫切。
4) comprehensive measurement
综合测量
1.
The development and the present situation of the comprehensive measurement were introduced and the technique was surveyed in the way of theory analysis together with mathematics calculation and computer simulation to successive and switching variable separately.
本文介绍了综合测量技术的发展和现状，并采用理论分析、数学计算与计算机仿真试验相结合的方法，分别对连续量和开关量的综合测量技术进行研究。
5) summary measure
综合测量
1.
This paper explores,theoretically and empirically,the relationship between the two kinds of such summary measures(overall health achievement index),one of which is constructed on the basis of implicit value judgment(internal weighting method),the other on the basis of external weighting method imposing direct weights to the indicator of health level as well as health distribution.
健康水平和健康分布的综合测量具有重要的理论和政策意义。
2.
On the basis of the HOPIT adjusted self report health data collected from Jiading,Baoshan,Jinshan and Chongming,4 Districts of Shanghai,this paper presented the disability concentration index as the summary measure of the distribution of population self report health.
基于经HOPIT模型校正后的上海市嘉定、宝山、金山和崇明4区(县)的人群自报健康资料,应用伤残集中指数进行人群自报健康分布的综合测量研究。
3.
This paper presented the summary measure of the level of population self-report health on the basis of household health service survey eon-ducted in the Jiading, Baoshan, Jinshan and Chongming, 4 districts of Shanghai.
该测量基于上海市嘉定、宝山、金山和崇明4区(县)的家庭卫生服务调查中的自报健康资料进行人群自报健康水平的综合测量研究。
6) multiple measurements combination method
多次测量综合方法
1.
Based on the analysis of the heat transfer mechanism inside the test piece with subsurface defect,this paper combined the identification algorithm study with the optimization of thermographic detection technique to develop a multiple measurements combination method(MMCM) to solve the.
结合对缺陷试件内部传热规律的分析,将缺陷边界的识别算法研究和缺陷的红外检测方法优化相结合提出了多次测量综合方法,从而解决了缺陷边界识别结果中部分边界对初始边界假设比较敏感的问题。
补充资料：《工业无线电干扰基本测量方法》(GB／T3907—1983)
《工业无线电干扰基本测量方法》(GB／T3907—1983)
General Methods of Measurement for Industrial Radio Interference
方法方面，采用二项式分布为依据的计数抽样检验，同时采用80%/即%准则，即保证在置信度至少为80%的情况下，受检的一批产品中至少有so%干扰电平值小于或等于规定的干扰允许值。根据《工业无线电干扰荃本测t方法》的规定对进人中国的电子设备、仪器和器件必须进行符合性检验，凡不符合要求的一律禁止进口，从而保护了中国的环境和广大消费者的利益。对中国生产的电子设备、仪器和器件进行严格的限制，对那些超过干扰允许值的产品要采取改进措施，否则将取消生产资格。在减少环境污染、保障人身健康和进出口贸易方面发挥越来越重要的作用，对提高中国电子设备、仪器和器件的质量产生了明显的效果。 (陈志田)以劝即ewuxiandianGanroojibenCell山均Fangfa《工业无线电干扰基本测.方法)(CB/T3叭)7一1983)(晓ne耐爪肠内汕ofAre山功阳万姆瓜for而以山‘耐双记如介*少~)机电、低压电器和电子设备，工业、科学.、医疗设备，机动车辆和其他点火装t，收音机和电视接收机，家用电器、电动工具及类似器具在工作中会发出射频电磁波，穿过其外壳或屏蔽产生干扰，影响电子设备和仪器的正常工作，危及人身安全和社会其他事业，称为无线电干扰。人们越来越认识到电磁波干扰己构成严重污染，必须用法律、标准加以控制，才能消除污染。首先要对产生干扰的工业千扰源进行测量，为此于1983年发布了(工业无线电干扰基本测量方法》(GBIT3义刀-1983)国家标准。该标准规定的测量方法是参照国际无线电干扰特别委员会(C巴PR)发布的(无线电干扰测量设备及测量方法规范》制定的。该标准规定了测t条件，对传导干扰电压测量、传导干扰电流测量、传导干扰功率测量和辐射干扰测量等，均采用了国际通用方法。在产品的抽样
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条