1) airfoil mixed-phase ice
翼型覆冰
1.
Based on the characteristics of airfoil mixed-phase ice caused by the wind which is vertical to conductor, a two-dimensional simulating model is established by FLUENT/GAMBIT and By Finite Volume Method(FVM), icing weight and properties at different velocity and humidity are compared respectively.
本文从输电线翼型覆冰过程的模拟入手,对覆冰导线的电磁场变化情况进行了数值解析,并定性的仿真了覆冰导线的舞振过程。
2) iced airfoil
结冰翼型
1.
Pressure distribution and stress calculation of glaze ice on iced airfoil
结冰翼型表面明冰的压力分布和应力计算
3) model of ice-coating
覆冰模型
1.
The article is attempt to propose a more appropriate model of ice-coating on transmission line in specific area based on the study of characteristics of ice-coating of transmission line in east and northeast Yunnan province as well as the analysis on national/international achievement in same field.
基于对滇东及滇东北地区电线覆冰特性研究和对国内外覆冰模型的分析,构建出较为适合研究区域的覆冰模型。
4) mode of freeing-rain-ice
覆冰计算模型
5) icing reappearing period model
覆冰重现期模型
6) icing
[英]['aɪsɪŋ] [美]['aɪsɪŋ]
覆冰
1.
Study on flashover arc mechanism of XZP/XZWP4-160 DC insulator under icing condition;
XZP/XZWP4-160直流绝缘子覆冰闪络电弧特性的研究
2.
Study on Icing Performance of 110kV Insulator Strings at AC Service Voltage;
工作电压下110kV交流绝缘子串覆冰特性研究
3.
Analysis of icing collapse of 500 kV Liu-Gui Transmission Line towers and some suqqestions;
500kV柳桂线铁塔覆冰破坏事故分析及建议
补充资料：有机覆层:有机覆层
在基体材料表面覆以有机材料的材料保护层。在机械製造中﹐有机覆层的绝大部分是涂装层﹐或称油漆层。此外﹐也有用橡胶或塑料作为覆层的。需要抗酸﹑硷和抗腐蚀性气体和液体的钢铁件﹐常用厚约 3毫米的橡胶(如氯丁橡胶)或塑料(如氯化亚乙烯共聚物)黏在表面﹐可长期保护基体不受腐蚀。这种覆层主要用在大型抗蚀容器或排气系统中。埋在土壤中的金属构件﹐常以聚乙烯带包裹保护。在喷鉬或喷不锈钢的表面上涂覆聚四氟乙烯﹐在150℃温度下摩擦係数很低﹐磨损轻微﹐适於製造低载荷和要求高度清洁的滑动轴承﹐或用在食品﹑精细包装和纺织机械上。各国的Du﹑Dx轴承都是以塑料与金属复合製成的。通过静电喷涂将环氧树脂﹑氯化聚醚﹑聚四氟乙烯以及聚氯乙烯等塑料粉末涂覆在金属表面﹐可获多种抗化学腐蚀性极好的覆层﹐可用於输水﹑污水处理和海洋平台的设备上。有机覆层在辉光放电情况下﹐有机单体可以聚合成无针孔的有机膜﹐用作电容器的介质层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条