1) mean of backlash
侧隙均值
2) average air-gap
气隙平均值
1.
In general condition,it should be allowed that eccentric error is larger than ±10% of average air-gap,but over-large eccentric value can produce very much unbalanced magnetic pull,and then increase the deflection of motor shaft,thus critical speed is influenced.
在一般情况下,气隙偏心误差不超过气隙平均值的上下10%是允许的,但过大的偏心值会产生很大的单边磁拉力,导致电机转轴挠度的增加,进而影响电机的临界转速,但许多电机设计人员在计算电机转轴的挠度时,往往忽略单边磁拉力对于挠度的影响,为此,介绍了单边磁拉力产生的原因及对电机转轴挠度影响的计算过程。
4) gap
[英][ɡæp] [美][gæp]
侧隙
1.
Because of a great amount of edge crack in pickled strips after cold rolling process, through making out the judging standard of qualified cutting quality and analyzing the influences of the gap and over lap on the cutting quality, corresponding connection of the gap and over lap with the thickness of strip steel is summarized out.
针对轧后酸洗带钢大量出现边裂的问题,通过制定切边质量判定标准,分析剪刃侧隙和重叠量对切边质量的影响,总结出了侧隙和重叠量与带钢厚度对应关系,该套参数编入程序应用表明,切边质量得到改善,出现边裂的概率减少到1!以下,节省了调整间隙的时间,提高了生产效率。
2.
Aiming at the disadvantage of the maintenance scheme,it points out that the bearing windage,gear gap and contact area should be adjusted correctly during the maintenance assembly process,which is used to en- hance the assembly adjustment quality and increase the running efficiency of the equipment.
分析堆取料机取料斗轮减速机输入轴与二级锥齿轮轴的故障原因,针对检修装配方案中的弊端,指出在检修装配过程中,应合格调整轴承游隙、齿轮侧隙以及接触区,以提高装配调整质量,提高了设备运转率。
5) Backlash
[英]['bæklæʃ] [美]['bæk'læʃ]
侧隙
1.
The Backlash Analysis of Hypoid Gears Based on Real Cutters;
基于实际切齿刀具的螺旋锥齿轮侧隙分析
2.
The Calculation and Analysis of the Backlash of The Gears used in Heavy Centrifugal Separator;
重型离心分离器齿轮副侧隙的计算与分析
6) side play
侧隙
1.
The results showed side play of trimmer's blade plays a decisive role in ensuring side trimming quality.
简介板带剪切变形过程,分析了影响切边质量的因素,剪刃侧隙是保证切边质量的重要因素,起决定性作用。
补充资料：气隙
分子式：
CAS号：
性质：在挤出涂层过程中，从模口到由压辊和冷却辊所形成的间隙（被涂覆材料在此被压平和冷却）之间的距离。也指在塑料的射频加热中电极和材料表面间的距离。
CAS号：
性质：在挤出涂层过程中，从模口到由压辊和冷却辊所形成的间隙（被涂覆材料在此被压平和冷却）之间的距离。也指在塑料的射频加热中电极和材料表面间的距离。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条