1) AISI 304 austenitic stainless steel
AISI 304奥氏体不锈钢
1.
Glow discharge nitriding and nitrocarburising in AISI 304 austenitic stainless steel were approached in this paper.
本课题针对AISI 304奥氏体不锈钢进行辉光离子渗氮和离子氮碳共渗研究。
2) AISI 304 stainless steel
AISI 304不锈钢
1.
Nanostructured surface layer was synthesized on an AISI 304 stainless steel by using surface mechanical attrition treatment (SMAT), the grain refinement behavior and the hardness variation were examined.
采用表面机械研磨处理(SMAT)在AISI 304不锈钢上制备出纳米结构表层,研究纳米化行为及其对硬度的影响。
4) AISI 440C
AISI 440C不锈钢
1.
AISI 440C stainless steel is considered as martensitic stainless steel, which is characterized with high carbon content, strength, hardness and wear resistance but poor in machinability.
AISI 440C不锈钢是一种高碳马氏体不锈钢,其含碳量高,强度、硬度和耐磨性高,切削加工性能差。
5) 304 austenitic stainless steel
304奥氏体不锈钢
1.
The influences of deformation rate on the mechanical properties of 304 austenitic stainless steel were studied by tensile test at room temperature.
采用室温拉伸实验研究了不同变形速度对304奥氏体不锈钢力学性能的影响规律。
2.
Solid Solution Nitriding of 304 Austenitic stainless steel and 3Cr13 Martensite stainless steel was investigated under the following technical parameters: temperature 900℃~1150℃,nitrogen pressure 0.
本文对304奥氏体不锈钢和3Cr13马氏体不锈钢的固溶渗氮进行了研究,固溶渗氮工艺参数的变化范围为:渗氮温度900℃～1150℃,氮气压力0。
3.
In this paper investigated the deep-drawing process of 304 austenitic stainless steel sheet and the friction and lubrication in the deforming process of the shell of permissible respirator self rescue from carbon monoxide.
本文研究了304奥氏体不锈钢自救器筒体制造工艺中的拉深工艺及摩擦润滑情况。
6) 304 Austenite Stainless Steel
304奥氏体不锈钢
1.
Effect of Cu on Strain-Induced Martensite Transformation in 304 Austenite Stainless Steel;
Cu对304奥氏体不锈钢应变诱发马氏体相变的影响
2.
Starting from lubricating status and drawing speed, the reasons of sticky lump caused by 304 austenite stainless steel drawing are analyzed, combining with actual situation of cooperating partner of the project, improving steps are provided, and proper lubricant is carried out.
从润滑状态及拉伸速度入手,分析了304奥氏体不锈钢拉伸时粘结瘤形成原因,结合项目合作单位的实际情况提出了改进措施,配制了合适的润滑剂。
3.
In the present paper, the effects of processing conditions on the deep-drawing deformation of 304 austenite stainless steel sheet were investigated by means of physic simulation and numerical simulation.
本文采用物理模拟和数值模拟技术，研究了拉深工艺条件对304奥氏体不锈钢拉深成形过程的影响规律。
补充资料：ai
发音要领
EssentialsofPronunciation
[ai],[ei],[ui]都是复韵母。前一个元音开口度大，发音长而响亮；后一个元音开口度小，发音短而轻，比较模糊。从前一个元音到后一个元音是自然滑行，不能跳跃。
[ai],[ei],[ui]areallcompoundfinals.Ineachofthem,theformervowelismoreopen,longerandlouderwhilethelatteroneisnarrow,short,weakandblurred.Itisimperativetohaveanaturalglidebutnotasuddenchangefromtheformertothelatter.
EssentialsofPronunciation
[ai],[ei],[ui]都是复韵母。前一个元音开口度大，发音长而响亮；后一个元音开口度小，发音短而轻，比较模糊。从前一个元音到后一个元音是自然滑行，不能跳跃。
[ai],[ei],[ui]areallcompoundfinals.Ineachofthem,theformervowelismoreopen,longerandlouderwhilethelatteroneisnarrow,short,weakandblurred.Itisimperativetohaveanaturalglidebutnotasuddenchangefromtheformertothelatter.
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条