1) NC placement
数控铺放
2) windrowing
[英]['windrəu] [美]['wɪnd,ro]
铺放
1.
The condition of sugarcane stalks outward windrowing, theoretical calculation formula of windrowing distance and angle were derived.
通过对抛出后甘蔗运动过程的高速摄影结果的分析,确立了甘蔗的运动形式,并进行了运动学分析,建立了数学模型,推导出了甘蔗向机车外铺放的条件、以及甘蔗铺放距离、铺放角的理论计算公式,采用Matlab编程,分析了整秆式甘蔗收获机圆弧轨道式柔性夹持输送装置甘蔗铺放过程中运动参数、结构参数以及甘蔗几何参数对甘蔗向外铺放、铺放距离、铺放角的相互影响规律,为甘蔗收获机的设计以及甘蔗铺放质量的提高提供了理论依据。
2.
The movement mode of sugarcane was confirmed by high speed photography test results about its movement process after being shot off from holding and conveying mechanism of sugarcane harvester, and the windrowing kinematics analysis of sugarcane was done.
通过对甘蔗抛出后运动过程的高速摄影结果的分析,确立了甘蔗的运动形式,并进行了运动学分析,建立了甘蔗收获机运动参数与夹持输送装置结构参数之间满足甘蔗向外铺放的条件。
3) open CNC
开放数控
1.
CNC technology based on PC has gone through over ten years, developing anew pattern of the open CNC, therefore, has fallen into three principal systemscentered on USA, Japan and Europe all over the world.
伴随计算机技术的快速发展,开放式控制技术,网络化技术和智能控制技术推动数控系统经历了一次体系结构的重大变革,以OSACA、OMAC和OSEC为代表的体系结构已基本形成开放数控的技术规范和应用体系,并竞争国际标准。
4) Open CNC
开放式数控
1.
Development of Web-based Networked Remote Monitoring and Control System on Open CNC Machine Tools;
基于Web的开放式数控机床网络化远程监控系统开发
2.
The Reserch and Development of Open CNC System Based on Software Reuse;
基于软件复用技术的开放式数控系统研究与开发
3.
Research on the High Performance and Open CNC Turning System for Non-circular Section Machining;
非圆截面开放式数控车削系统的研究
5) open CNC system
开放式数控
1.
The research of the application of PMAC & COM on open CNC system;
PMAC&COM在开放式数控系统平台设计中的应用研究
2.
A summary of the study on open CNC system;
开放式数控系统研究综述
3.
CNC system is gradually developing toward flexible, component modular and re-configurable of open CNC system's structure.
用软件复用 ,软件重构等软件开发新技术对开放式数控系统进行研究 ,已成为一种趋势。
6) open architecture NC
开放式数控
1.
The Open architecture NC system has some advantages such as logic independence of the module,interface standardization,flexibility and portability.
开放式数控系统具有模块逻辑独立、接口标准化、可移植性好的特点,成为当前数控系统的主要发展趋势。
2.
The Open architecture NC system has some advantages such as logic independence of the module, interface standardization, flexibility and portability.
开放式数控系统具有模块逻辑独立、接口标准化、柔性和可移植性好的特点,它满足了制造业对产品多样化的要求,成为数控系统的主要发展趋势。
补充资料：铺放
1.陈列放置。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条