3) Compressor blade
压气机叶片
1.
Recent applications and research of erosion resistant coating of compressor blade are summarized.
综述了压气机叶片抗冲蚀涂层的研究进展、应用情况以及为了改善涂层性能而进行的多元合金化、多层涂层方面的研究,展望了今后压气机叶片抗冲蚀涂层的发展方向。
2.
Fine grain cast IN718 compressor blade form abroad has been analyzed.
解剖、分析了国外细晶铸造IN718压气机叶片。
3.
The structure design and off set optimization of compressor blades are conducted by the system, and as a result, the blades are restructured.
对航空发动机压气机转子叶片结构进行了特征分析和归纳,提取了典型特征结构和特征参数,建立了基于UG软件的压气机叶片特征设计系统,利用该系统进行了叶片的特征结构设计和多种形式的罩量优化,在此基础上对叶片结构进行了重构。
4) Compressor Impeller
压气机叶轮
1.
Taking into consideration the material nonlinearity of turbocharger compressor impellers and turbine wheels,we carry out elastoplasticity numerical analysis of their burst speed based on FEM software ANSYS.
基于ANSYS有限元分析软件,对车用涡轮增压器涡轮叶轮和压气机叶轮进行了材料非线性弹塑性有限元数值分析,计算了涡轮叶轮和压气机叶轮在离心载荷作用下的破裂转速,并与试验结果进行了对比。
2.
From the analysis of compressor impeller of vehicle turbocharger stress characters,the calculation and analysis methods of impeller structural strength were described.
通过对车用增压器压气机叶轮内应力特点的分析,确定了叶轮强度的计算方法,介绍了利用有限元分析软件对叶轮内部应力进行分析的过程,并就强度分析中的关键步骤和技术难点进行了讨论。
3.
A compressor impeller with a diameter of 120 mm has been machined successfully with this system.
运用该系统编制了直径 12 0 mm的压气机叶轮的五轴加工程序 ,并成功地进行了叶轮加工 。
5) impeller
[英][im'pelə] [美][ɪm'pɛlɚ]
压气机叶轮
1.
Based on the FE parametric quadratic programming(PQP) method,the stress distribution of 3-D frictional contact problem of impeller-shaft sleeve-shaft assembly was analyzed.
以某柴油机涡轮增压器的压气机为例,基于多重子结构技术,建立了增压器压气机叶轮、轴套和轴的三维整体有摩擦弹性接触的计算模型,采用有限元参数二次规划法,对其进行有限元分析。
6) compressor stator
压气机静叶
1.
The potential of predicting separations in turbomachinery of detached eddy simulation (DES) was researched by applying it to simulate high Reynolds-number complex flows of compressor stator with massive separations near endwalls.
将分离涡模拟方法应用于高雷诺数压气机静叶有大分离的复杂流动计算中,研究该方法对分离的模拟能力。
补充资料:压气
1.平息怒气。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条