1) high temperature reflux
高温回流
1.
In this thesis,appropriate route for ZnO-Au Hybrid nanocrystals (HNCs) was obtained by comparing reverse microemulsion, aqueous chemical methods and high temperature reflux.
本研究通过综合比较反相微乳液、水相化学及高温回流等方法,确定了高温回流法是制备ZnO-Au杂化纳米晶的最佳工艺路线。
2) high temperature gases recirculating
高温烟气回流
1.
Two 420t/h corner anthracite-fired boilers of Jao Zuo AES Wan Fang Power Company Limited were successfully retrofitted by using high temperature gases recirculating tech-nology, pulverized coal enrichment technology and staged combustion technology.
该文就焦作爱依斯万方电力有限公司2台420 t/h无烟煤锅炉运用高温烟气回流技术、煤粉浓缩技术、分级燃烧技术,进行了成功的改造,在低负荷稳燃、降低飞灰可燃物、减少炉膛出口两侧烟温偏差、提高锅炉效率等方面均取得较为显著效果。
3) high-temperature tempering
高温回火
1.
Furthermore,the best grain refinement heat treatment process for this material is twice sub-temperature quenching+high-temperature tempering process.
指出该材料最佳的晶粒细化热处理工艺是:两次亚温淬火+高温回火工艺。
2.
It is learned that the theory of removing sclerosis of residual austenite after transformation and theory of carbide deposition has different effect during different time in high-temperature tempering.
对18Cr2Ni4WA钢渗碳层中残余奥氏体在高温回火中转变机制进行研究,得知相变硬化消除理论和碳化物析出理论在高温回火的不同时间中的不同作用,提出：680℃×3h空冷回火,650℃×2h空冷回火,810℃×15min空冷淬火,180℃×1。
4) high temperature tempering
高温回火
1.
By means of three times procssing at high temperature tempering,the coarse nonequilibrium structure of 85Cr 2Mn 2Mo steel recrystallizes absolutly ,the austenite grain was effectively refined and structure heredity was cut.
本文在研究85Cr2Mn2Mo钢的组织遗传的基础上,着重研究了该钢组织遗传的消除,文中采用三次高温回火工艺,使85Cr2Mn2Mo钢的粗大的非平衡组织发生充分的再结晶,有效地细化了奥氏体晶粒,切断了组织遗传。
2.
The high temperature tempering can eliminate the residual stress caused by quenching, this can avoids the deformation in the following electric machining; after ultralow-temperature disposal process, the wear resistance of die increases 2 to 3 times, so its using time is consumedly prolonged.
高温回火可消除模具淬火时产生的残余应力,避免模具在后续的电加工中产生变形;而采用超低温工艺处理后,模具的耐磨性可提高2～3倍,延长了模具的使用寿命。
3.
In this paper,the relationships of structures and properties of 10Cr9MolVNbNsteel austenization normalizing at different temperature and time and dustenizationnormalizing and high temperature tempering following aging at 580 - 660℃ for zero to5000h were studied by means of transmission electron microscope (TEM) and scanningelectron microscope (SEM).
本文采用透射电镜、扫描电镜等手段研究了10Cr9Mol VNbN钢不同温度和时间奥氏体化正火后以及正火高温回火后再经580～660℃时效0～5000h的组织和性能的关系。
5) High temperature recovery
高温回复
6) high Temperature melt down
高温回炉
补充资料：高温
较高的温度，在不同的情况下所指的具体数值不同，例如在某些技术上指几千摄氏度以上，在工作场所指32摄氏度以上。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条