1) Annealing craft system
退火工艺制度
2) rolling and annealing
轧制退火工艺
1.
AZ31 magnesium alloy sheets are treated through different rolling and annealing procedures.
采用不同轧制退火工艺处理AZ31变形镁合金,采用分离式Hopkinson压杆测试了不同微观组织镁合金的动态力学性能,研究了组织结构与材料动态力学响应之间的关系,探讨了应变率效应。
3) annealing process
退火工艺
1.
Effect of annealing process on properties of CaBi_(4.3)Ti_4O_(15) ferroelectric thin films;
退火工艺对CaBi_(4.3)Ti_4O_(15)铁电薄膜性能影响
2.
Effect of annealing process on microstructure and texture of alloying hot dip galvanized Ti-IF sheet;
退火工艺对Ti-IF钢合金化热镀锌板微观组织织构的影响
3.
The influence of cold-rolling and annealing process on cold-rolling sheet texture evolvement for Baotou Iron and Steel(Group) Co.;
冷轧及退火工艺对包钢CSP薄板织构演变的影响
4) annealing technology
退火工艺
1.
The effect of the rolling technology(inverting techniques)and final product annealing technology properties(such as mechanical properties,deep-drawing property,hardness and so on)of Mo sheets is discussed in this paper.
讨论了轧制工艺(换向工艺)、成品退火工艺对钼片性能(力学性能、深冲性能、硬度等)的影响。
2.
In this article the annealing technology of NTD single silicon is introdued.
本文简要介绍了NTD硅单晶的退火工艺 ,通过在一次退火工艺和二次退火升τ工艺中 ,引入P2 O5,结果表明 :晶体表面的P2 O5保护层在晶体表面的吸除作用能引起晶体内缺陷和杂质的消失 ,使晶体的少子寿命τ及τ的合格率大幅度升
3.
The effect of main processing parameters, such as deformation rate and annealing technology in cold rolling deep-drawing properties of the strip were studied.
本文以涟钢DDQ级冷轧深冲板为研究对象,主要是根据用户对冷轧深冲薄板的质量要求,结合涟钢实际情况,研究不同的冷轧压下率和不同的退火工艺对冷轧深冲板深冲性能的影响,改进现有的生产工艺制度。
5) anneal process
退火工艺
1.
To do anneal process of bearing steel wire rod experiments with the furnace,a set of sphe.
对轴承钢盘条在强对流罩式炉中的退火工艺进行试验 ,摸索出一套球化退火和再结晶退火工艺。
2.
This article introduces the anneal process,step,main point of50ton convertor,especially for the installation of heating device,operation and temperature control of anneal heat treatment.
介绍50t转炉炉壳的整体退火工艺过程、步骤、要点,着重介绍了加热装置的安装、操作及退火热处理温度的控制。
6) annealing
[英][ə'ni:liŋ] [美][ə'nilɪŋ]
退火工艺
1.
The joint strength of titanium and stainless steel by explosive welding and the effect on property of interface under different annealing temperature are investigated in this paper.
通过拉伸试验、组织分析、断口形貌分析以及焊缝显微硬度的测定 ,研究了钛 不锈钢爆炸焊接接头强度及退火工艺对焊接接头强度的影响。
2.
In this paper, an annealing process has been adopted to regain the plastic property of the steel back while the other properties of CG03 brake linings are still remained.
采用一种退火工艺，在保持刹车片其它性能的同时，使刹车片钢背恢复塑性。
补充资料：软化退火(见低温退火)
软化退火(见低温退火)
soft-annealing
rU0nhUO tUihUO软化退火(soft一annealing)见低温退火。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条