1) Screw Thread Joints in an Auto
![点击朗读](/dictall/images/read.gif)
汽车上的螺纹连接
2) pipe union
![点击朗读](/dictall/images/read.gif)
管子的螺纹连接
3) connecting thread
![点击朗读](/dictall/images/read.gif)
连接螺纹
1.
Mechanics analysis and design of connecting thread in casing drilling;
![点击朗读](/dictall/images/read.gif)
套管钻井中连接螺纹力学分析及设计计算
2.
Numerical analysis and research of strength in connecting thread when unguided rocket launching;
火箭弹发射时连接螺纹处强度的数值分析和研究
3.
An axial symmetry of a drill connecting thread and three-dimensional finite element model were established.
建立了钻具连接螺纹的轴对称和三维空间有限元模型,分析了钻具螺纹在给定上扣扭矩作用下外螺纹和内螺纹的应力变化。
4) thread connection
![点击朗读](/dictall/images/read.gif)
螺纹连接
1.
An analysis of the strength of the thread connection of submarine casing suspender
![点击朗读](/dictall/images/read.gif)
水下套管悬挂器螺纹连接强度分析
2.
Experiments showed that this unique internal thread form with torque-angle tightening method could effectively provide commitment of thread connection for the new bearing.
最后确定装配线上的螺纹连接的转角扭矩拧紧工艺。
5) threaded connection
![点击朗读](/dictall/images/read.gif)
螺纹连接
1.
The application of steel bar threaded connection technology among bridge construction;
![点击朗读](/dictall/images/read.gif)
钢筋螺纹连接技术在桥梁施工中的应用
2.
The problem of gas leakage caused by the hose falling out is solved by means of threaded connection of a specified length bellows to the hotplate.
在居民用户室内燃气工程中采用不锈钢波纹管,安装L型灶前台式阀,通过波纹定尺管与灶具螺纹连接,解决了胶管脱落引发燃气泄漏的问题。
3.
Application of several typical threaded connection components presented in the paper would provide designer with some reference.
电子设备中常用的铝、镁、塑料等低强度工程材料上直接生成的螺纹强度及承载能力都不高,不易满足设计需要,本文介绍几种典型螺纹连接元件的应用,以期能为设计师提供一定的参考。
6) threaded coupling
![点击朗读](/dictall/images/read.gif)
螺纹连接
1.
Action analysis of a coupling structure to threaded coupling;
![点击朗读](/dictall/images/read.gif)
一种连接结构对螺纹连接的影响分析
补充资料:攻螺纹、套螺纹及其注意事项
常用的在角螺纹工件,其螺纹除采用机械加工外,还可以用钳加工方法中的攻螺纹和套螺纹来获得。攻螺纹(亦称攻丝)是用丝锥在工件内圆柱面上加工出内螺纹;套螺纹(或称套丝、套扣)是用板牙在圆柱杆上加工外螺纹。
一、攻螺纹
1.丝锥及铰扛
(1)丝锥
丝锥是用来加工较小直径内螺纹的成形刀具,一般选用合金工具钢9SiGr制成,并经热处理制成。通常M6~M24的丝锥一套为两支,称头锥、二锥;M6以下及M24以上一套有三支、即头锥、二锥和三锥。
每个丝锥都有工作部分和柄部组成。工作部分是由切削部分和校准部分组成。轴向有几条(一般是三条或四条)容屑槽,相应地形成几瓣刀刃(切削刃)和前角。切削部分(即不完整的牙齿部分)是切削螺纹的重要部分,常磨成圆锥形,以便使切削负荷分配在几个刀齿上。头锥的锥角小些,有5~7个牙;二锥的锥角大些,有3~4个牙。校准部分具有完整的牙齿,用于修光螺纹和引导丝锥沿轴向运动。柄部有方头,其作用是与铰扛相配合并传递扭矩。
(2)铰扛
铰扛是用来夹持丝锥的工具,常用的是可调式铰扛。旋转手柄即可调节方孔的大小,以便夹持不同尺寸的丝锥。铰扛长度应根据丝锥尺寸大小进行选择,以便控制攻螺纹时的扭矩,防止丝锥因施力不当而扭断。
2.攻螺纹前钻底孔直径和深度的确定以及孔口的倒角
(1)底孔直径的确定
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条