1) differential gain error
![点击朗读](/dictall/images/read.gif)
微分增益误差
2) gain error
![点击朗读](/dictall/images/read.gif)
增益误差
1.
Channel mismatches errors include offset error,gain error and time error.
![点击朗读](/dictall/images/read.gif)
通道失配误差包括偏置误差、增益误差和时间误差。
2.
To remove the offset error and the gain error in the data acquisition system (DAS) and satisfy the accuracy and real-time requirements of the system, a FPGA-based self-calibration method for data acquisition is presented.
为消除数据采集系统中的失调误差和增益误差,满足系统实时性要求,提出了一种基于FPGA的数据采集自校准方法。
3.
Because mismatches,such as offset error,gain error as well as time-skew error,may degrade SINAD(signal-to-noise-and-distortion ratio) of the time-intetrleaved ADC(TIADC) system,an explicit analysis of such three channel mismatch effects in the time-interleaved ADC system based on the filter-bank method was presented.
通道失配误差(如偏置误差、增益误差和时间相位误差)严重降低了并行交替型ADC(time-interleaved ADC,TIADC)系统的信纳比。
4) differential gain
![点击朗读](/dictall/images/read.gif)
微分增益
1.
Issues needing attention are pointed out,and the measurements of signal to noise ratio,differential gain,differential phase and impulse characteristics are introduced in detail.
对具有模拟输入输出的数字视频设备,为解决测量结果不稳定性和不一致性,提出了改进的测量方法,指出了测量中应注意的问题,并具体介绍了信噪比、微分增益、微分相位及脉冲特性的测量。
2.
We discussed mainly the gain, differential gain, threshold current of Si-based quantum-dot laser and the dependence of threshold current on temperature from discrete energy level of thr.
本文阐述了Si基光发射材料的研究进展及它在硅基光电子集成中的重要地位,从三维受限量子点的分立能级和δ函数状的态密度分布入手,着重讨论了Si基量子点激光器的增益、微分增益、阈值电流及阈值电流的温度特性。
3.
The causes of video signal nonlinear distortion, differential gain and differential phase are discussed.
介绍了视频信号非线性失真的原因、微分增益与微分相位,讲述了音视频产品的视频线性失真与非线性失真的测量原理以及改进方法。
5) error amplifier gain
![点击朗读](/dictall/images/read.gif)
误差放大器增益
6) Gain and phase errors
![点击朗读](/dictall/images/read.gif)
增益和相位误差
补充资料:布里斯托尔相对增益
分子式:
CAS号:
性质:在一个装置上设置多个控制系统时,系统间会存在相互耦合。但其关联程度可用布里斯托尔相对增益λij来衡量。相对增益λij的定义是在其他控制系统均为开环时,第j个控制变量Uj对第i个输出变量Yi通道的放大系数(增益)与该通道在其他控制系统均为闭环时放大系数(增益)之比,称为相对增益。由于是布里斯托尔提出的,所以又称布里斯托尔相对增益。当系统间无耦合时,一个控制回路是处于开环或闭环状态,对另一个控制回路是不会起影响的,故λij=1。但在系统间存在耦合时,情况就不同了,耦合越严重,一个控制回路处于开环或闭环,对其他控制回路影响就越大,λij偏离l就越远。因此,相对增益λij可用来衡量控制系统间关联的程度。
CAS号:
性质:在一个装置上设置多个控制系统时,系统间会存在相互耦合。但其关联程度可用布里斯托尔相对增益λij来衡量。相对增益λij的定义是在其他控制系统均为开环时,第j个控制变量Uj对第i个输出变量Yi通道的放大系数(增益)与该通道在其他控制系统均为闭环时放大系数(增益)之比,称为相对增益。由于是布里斯托尔提出的,所以又称布里斯托尔相对增益。当系统间无耦合时,一个控制回路是处于开环或闭环状态,对另一个控制回路是不会起影响的,故λij=1。但在系统间存在耦合时,情况就不同了,耦合越严重,一个控制回路处于开环或闭环,对其他控制回路影响就越大,λij偏离l就越远。因此,相对增益λij可用来衡量控制系统间关联的程度。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条