1) density of charging current
充电电流密度
2) charging density
充电密度
3) current density
电流密度
1.
Effect of current density on performances of deposit in low-temperature iron plating process;
低温镀铁时电流密度对镀层性能的影响
2.
Research and application on current density of ion exchange membrane electrolyzer;
离子膜电槽电流密度的研究及应用
3.
Effects of anode current density on micro-arc oxidation ceramic coating of aluminum alloy;
阳极电流密度对铝合金微弧氧化陶瓷膜的影响
4) electrical current density
电流密度
1.
The influences of electrical current density of Joule heating treatment on GMI effects of amorphous Co_(68.
本文研究了焦耳处理工艺的处理电流密度对Co68。
5) Electric current density
电流密度
1.
The electric current density fields superposition principle and its applications;
电流密度场叠加原理及其应用
2.
The relation between electric current density and electric current efficiency and the optimum conditions, i.
通过实验获得了三槽隔膜式离子水设备制取弱碱性水的电极距离、电压、盐水浓度等影响因素的最佳参数,以及电流密度与电流效率的关系。
3.
The performance comparison tests of sacrificing anodes of zinc alloy, common magnesium alloy and high electric potential magnesium alloy in the standard liquid of simulated soil media show that, with increasing electric current density, the open-circuit potential and working potential of three anodes will gradually become positive and electric current efficiency will become increasingly greater.
锌合金、普通镁合金和高负电位镁合金牺牲阳极在模拟土壤介质的标准溶液中进行电化学性能对比试验 ,表明 :随着电流密度的增加 ,三种阳极的开路电位、工作电位逐渐变正 ,电流效率增大。
6) constant current density
恒电流密度
1.
AAO templates with different pores were prepared by constant current density process instead of constant voltage oxidation process in sulphuric acid,oxalic acid and phosphoric acid respectively.
由于传统恒压氧化方法的局限性,为得到不同孔径高度有序的阳极氧化铝模板(AAO),采用改进的恒电流密度法,分别在硫酸、草酸和磷酸电解液中制备了不同孔径的阳极氧化铝模板,并借助扫描电子显微镜(SEM)观察了膜的微观形貌,研究了电解液、电流密度等对膜的影响。
2.
Anodic aluminum oxide (AAO) is fabricated by constant current density process in oxalic acid and phosphoric acid electrolyte respectively.
采用恒电流密度法,分别在草酸和磷酸的电解液中制备了阳极氧化铝模板(AAO),借助扫描电镜(SEM)观察了膜的微观形貌,结合恒电压法制备的AAO模板,研究了电解液、电流、电压等对膜的影响,并且探讨了恒电压和恒电流密度法的形成机理。
3.
Aiming at resistance characteristic of porous metal materials, the theoretic model of strip porous metal material was firstly established through continuous and multilevel constant current density electrodeposi-tion under perpendicular movement state.
为了对电沉积法制备多孔金属的设备制造和在线控制提供理论指导,针对多孔金属的电阻特性,初次建立了垂直方式运动状态下,带状多孔金属材料连续多级恒电流密度电沉积模型,推导出阳极长度、形状、安装位置、运行速度和总电流的计算公式,对电沉积法制备多孔金属材料的生产线设计和在线控制具有应用价值。
补充资料：充电
分子式：
CAS号：
性质：蓄电池从外电路接受电能，转化为电池的化学能的工作过程。蓄电池在其能量经放电消耗后，通过充电恢复，又能重新放电，构成充放循环。一般用直流电流(也有用不对称交流电流或脉冲电流)充电。不同情况下，采用不同的充电方法如恒流充电、恒电压充电、浮充电、涓流充电、急充电或这些方法的组合式充电等。
CAS号：
性质：蓄电池从外电路接受电能，转化为电池的化学能的工作过程。蓄电池在其能量经放电消耗后，通过充电恢复，又能重新放电，构成充放循环。一般用直流电流(也有用不对称交流电流或脉冲电流)充电。不同情况下，采用不同的充电方法如恒流充电、恒电压充电、浮充电、涓流充电、急充电或这些方法的组合式充电等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条