1) upper leather finish
面革涂饰剂
2) leather finishing agent
皮革涂饰剂
1.
The relationship between the photoinitiator composition of the UV curable leather finishing agents,monomer,auxiliary agent and the apparent performances of coating film for leather was studied.
研究了UV固化皮革涂饰剂的光引发剂、光活性单体、助剂与皮革力学性能及表观性能的关系,并对皮革表面微观性能及透气度进行了表征。
2.
Many improvements emerged as it was applied in preparation of leather finishing agent.
以该共聚物为表面活性剂与丙烯酸酯类进行乳液聚合制备了皮革涂饰剂,应用于皮革涂饰后,革样的物理机械性能较采用常规乳化剂制备的丙烯酸树脂涂饰革样抗水性提高了28。
3.
The modified acrylic resin leather finishing agent with hydroxyl silicon oil was synthesized by the condensation product and acrylic resin monomer emulsion.
通过硅烷偶联剂(KH570)的水解产物与羟基硅油发生缩合反应向羟基硅油分子中引入C=C双键,在过硫酸铵引发下,缩合产物再与丙烯酸酯单体发生乳液聚合合成了羟基硅油改性丙烯酸树脂皮革涂饰剂。
3) leather coating agent
皮革涂饰剂
1.
Acrylic leather coating agents produced by Rohm-Haas company are recognized as leading technology in the word.
通过分析近30年公开的专利,对Rohm-Haas公司关于丙烯酸皮革涂饰剂的研究思路和研究方法进行概述。
4) leather finishing
皮革涂饰剂
1.
A series of waterborne polyurethane emulsions modified by copolymerization with WACKER IM 22、RHODORSIL OIL 1647 V60、KF-6001 and traditional hydroxy-terminated silicon oil respectively for leather finishing were synthesized, and characterized with GPC, DSC, TEM and TGA and their finishing properties on leathers were measured.
引言水性聚氨酯是一类重要的皮革涂饰剂,它耐磨、柔韧性好,可增加皮革的美观和耐用性。
2.
The classification, preparation and development of waterborne polyurethane for leather finishing were viewed in this paper.
本文综述了水性聚氨酯皮革涂饰剂的分类、制备和发展概况 ,详细讨论了水性聚氨酯皮革涂饰剂的结构与性能的关系及其改性研究 ,指出了水性聚氨酯皮革涂饰剂的发展趋势。
3.
Preparation of Polyether polyol and its applications in the production of leather finishing have been prescnted in this article.
叙述了用于皮革涂饰剂生产上的聚醚多元醇制备及在皮革涂剂生产上的应用。
5) maxwhite
['mækswait]
白革涂饰剂
6) coating finish for shoe upper leather
鞋面革涂饰
补充资料：面革
分子式：
CAS号：
性质： 轻革的一个重要品类。泛指鞋面革。主要有正面革、修正面革、绒面革等品种。多用猪、牛、羊皮为原料，以铬鞣制作，一般染成各种颜色并经乳液加油。除绒面革及个别不涂饰革外，大多是经涂饰的。其厚度按不同原料皮及制鞋的要求而变化（在0.5~1.8mm之间），不带衬里的厚型鞋面革可达2.5mm以上。面革的质量应符合国家主管部门颁布的质量标准，并要求空着舒适耐用。
CAS号：
性质： 轻革的一个重要品类。泛指鞋面革。主要有正面革、修正面革、绒面革等品种。多用猪、牛、羊皮为原料，以铬鞣制作，一般染成各种颜色并经乳液加油。除绒面革及个别不涂饰革外，大多是经涂饰的。其厚度按不同原料皮及制鞋的要求而变化（在0.5~1.8mm之间），不带衬里的厚型鞋面革可达2.5mm以上。面革的质量应符合国家主管部门颁布的质量标准，并要求空着舒适耐用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条