说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 流送量调节
1)  feed flow adjustment
流送量调节
2)  flow adjustment
流量调节
1.
It is showed through tests and analysis that when sampling time is one second and control scheme of single closed loop flow adjustment system and digital adjuster of proportion integral are adopted,the requirement of flow control can be reached.
试验分析表明,选择水、油相流量的采样时间为1s,采用单闭环流量调节系统的控制方案、比例积分数字调节,完全能够达到流量控制要求。
3)  flow regulating
流量调节
1.
According to analysis of flow regulating,flow range and flow characteristic for conerol valve,the artile introduces some factors which must be considered during the choose and design of control valve.
通过对调节阀的流量调节、调节范围及流量特性的分析,介绍了调节阀设计及选型中需考虑的几个因素。
2.
The Paper elaborates the necessity of air gas flow regulating in view of production operation and economic efficiency and puts forward treatment measures for air gas flow regulating and makes technical analysis and economic comparison.
以某工程为例,从生产运行和经济效益方面,阐述了煤气流量调节的必要性,提出了煤气流量调节的处理措施,并进行了技术分析和经济比较。
4)  Flow control
流量调节
5)  flow regulation
流量调节
1.
Total system flow regulation in long distance water diversion works with multistage pump stations;
长距离多级泵站引水工程全系统流量调节
2.
The strengths for flow regulation and superheat adjustment of electronic expansion valve are purposed,as well as the development trend is analyzed in air-conditioning or commercial freezing area.
从制冷系统节流机构的流量调节稳定性、过热度控制原理、系统节能、瞬态反应特性、部分负荷调节特性方面,比较分析了几种节流机构应用于制冷装置中的特点。
3.
To this problem,the variable-frequency speed regulation and flow regulation split-ranging coordinated control of the centrifugal pump for energy saving is given.
离心泵的变频调速是目前广泛采用的流量调节方法,高效节能是其最大优点,但是当流量降低时,可能造成压头过低而影响后续流程。
6)  flow adjusting
流量调节
1.
This paper also offers a method of measuring the flowing resistance characteristics and the character parameters on the basis on analysing the structure and flow adjusting characteristics of the regulator.
在对调节阀的结构和流量调节特性分析的基础上。
2.
The effective movement region is the research region of the flow adjusting characteristics of regulator.
有效行程区是调节阀流量调节特性所研究的区域。
补充资料:理想流量计试探与流量仪表的选用
理想流量计试探
  
  1.检测件无阻碍物;
  2.检测件可夹装在管道外部,可随意移动在任何地点测量而无须截断管道与流体;
  3.仪表的流量计算方程简单明确,可外推到未知领域而无须实流校验;
  4.频率脉冲输出信号,数字式仪表,便于远传抗干扰及与计算机联网;
  5.仪表输出信号不受流体介质物性的影响;
  6.仪表输出信号不受流体流动特性的影响;
  7.仪表复现性高;
  8.仪表范围度宽,线性好;
  9.仪表可靠性高,价格适宜,维修技术不复杂;
  10.无须个别实流校验,或只须“干校”,或在一、二种介质中校验可推广到各种介质;
  11.检测件输出信号直接反映质量流量。

  可以说至今并没有出现上述的理想流量计,所有流量计都多少具备一些上述条件,只不过有的多些,有的少些。所有流量计制造厂试制新产品都力图能更多地具备上述条件。


流量仪表的选用
  
   流量仪表的选型对仪表能否成功使用往往起着很重要的作用,由于被测对象的复杂状况以及仪表品种繁多,产品质量难以掌握等情况,使得仪表的选型感到困难。没有一种十全十美的流量计,各类仪表都有各自的特点,选型的目的就是在众多的品种中扬长避短,选择自己最合适的仪表。

   一般选型可以从五个方面进行考虑,这五个方面为仪表性能方面、流体特性方面、安装条件方面、环境条件方面和经济因素方面。五个方面的详细因素如下:  

  1.仪表性能方面

  准确度、重复性、线性度、范围度、流量范围、信号输出特性、响应时间、压力损失等;

  2.流体特性方面

  流体、温度、压力、密度、粘度、化学腐蚀、磨蚀性、结垢、堵塞、混相、相变、电导率、声速、导热系数、比热容,等熵指数;

  3.安装条件方面

  管道布置方向,流动方向,检测件上下游侧直管段长度、管道口径、维修空间、电源、接地、辅助设备(过滤器、消气器)、安装、脉动等;

  4.环境条件方面

  环境温度、湿度、电磁干扰、安全性、防爆、管道振动等;

  5.经济因素方面

  仪表购置费、安装费、运行费、校验费、维修费、仪表使用寿命、备品备件等。


  仪表选型的步骤如下:

  1. 依据流体种类及五个方面考虑因素初选可用仪表类型(要有几类型以便进行选择);
  2. 对初选类型进行资料及价格信息的收集,为深入的分析比较准备条件;
  3. 采用淘汰法逐步集中到1-2种类型,对五个方面因素要反复比较分析最终确定预选目标。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条