1) nutation drive pins
章动传动销
2) Nutation drive
章动传动
1.
A new kind of internal bevel gear nutation drive is studied The optimization design of the drive, considering 16 constraints such as strength, interference, lubrication and nutation angle and so on, is provided On the basis of the theory, a multi objective function is presented, which ensures that the drive obtains the minimum gyromoment and volume, and the maximum efficienc
针对内啮合锥齿轮少齿差章动传动 ,结合考虑齿轮强度、齿形干涉、润滑状态、章动角等约束条件 ,提出了以传动效率最高、陀螺力矩最小、体积最小或重量最轻为目标函数的多目标优化设计方法 ,并研制了相应的计算、分析应用软
2.
This paper proposes a novel method for calculating the rotational inertia for uniform bevel gear rotated around the slantwise axis inclined with an angle and develops a mathematical model for dynamic characteristics analysis of a nutation drive system composed of concave and convex meshing bevel gears by Lagrange dynamic equation.
给出了锥齿轮对与其轴线成一定夹角偏心轴的转动惯量的计算方法,并应用拉格朗日动力学方程对内啮合锥齿轮少齿差章动传动系统进行了动力学分析,最后对章动传动系统中的螺旋锥齿轮进行了运动学分析。
3) pin gearing
销齿传动
1.
Application of pin gearing in the vertical movable bridge;
销齿传动在开启桥上的应用
2.
This paper discusses the problems the computing method of pin gearing in the present machinery design handboods, deduces the theoretical computing formula for overlap coefficient and determines the limiting value of gear tip radius.
指出现有机械设计手册中销齿传动的重合度求法存在的问题，推导出重合度理论计算公式，同时确定了齿轮齿顶圆半径的取值范
3.
This paper describes the principle of the working of pin gearing, infers the mathematical expression: overlap caefficien≥1, proves that under certain conditions when there is a smaller number of teeth, the expression of overlap coeffcient≥1 is still valid, and finally concludes by indicating the advantages of application of pin gearing in the packaging machinery.
本文叙述了销齿传动的工作原理，推导出销齿传动中啮合重叠系数≥1的数学表达式，肯定了在一定条件下销击中的齿轮齿数较少时仍能满足重叠系数≥1，并指出在包装机械中运用销齿传动的优越性。
4) pin gear transmission
销齿传动
1.
Courrently the analysis of bending intension of vice gear of pin gear transmission is still on the basis of the traditional theory of intesion and the supposing computating method of actionless intension,comparing with the present technology request,which has the certain disparity and is to study for further performs thoroughly.
当前,对于销齿传动齿轮的弯曲强度分析仍然是基于传统强度理论和假设的静强度计算方法,与目前的技术要求存在一定的差距,有待进一步加以深入研究。
2.
The computer assisted optimization design of the rifeness used involute column gear transmission has already been researched a great many,but the optimizing design about application increasing pin gear transmission still has not been seen as yet.
本文对销齿传动的计算机辅助优化设计作了初步探讨,试图对从事齿 轮传动设计的同仁能有所益处。
6) driving pin
传动销
补充资料：传动：摆线针轮传动
由外齿轮齿廓为变态摆线﹑内齿轮轮齿为圆销的一对内嚙合齿轮和输出机构所组成的行星齿轮传动。除齿轮的齿廓外﹐其他结构与少齿差行星齿轮传动相同。摆线针轮行星减速器的传动比约为6～87﹐效率一般为0.9～0.94。图 轮齿曲线的形成 为轮齿曲线的形成原理。发生圆在基圆上滚动﹐若
大於r1﹐M'点画出的是长幅外摆线﹔若
小於r1﹐M''点画出的是短幅外摆线﹔用这些摆线中一根曲线上的任意点作为圆心﹐以针齿半径rz为半径画一系列圆﹐而后作一根与这一系列圆相切的曲线﹐得到的就是相应的长幅外摆线齿廓或短幅外摆线齿廓﹐其中短幅外摆线齿廓应用最广。用整条短幅外摆线作齿廓时﹐针轮和摆线轮的齿数差仅为1﹐而且理论上针轮有一半的齿数都与摆线轮齿同时嚙合传动。但如果用部分曲线为齿廓就可得到两齿差和三齿差的摆线针轮传动。用长幅外摆线的一部分作轮齿曲线时﹐其齿廓与圆近似﹐并与针齿半径相差不大﹐因此可用它的密切圆弧代替。摆线针轮传动的优点是传动比大﹑结构紧凑﹑效率高﹑运转平稳和寿命长。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条