1) zine liner
锌衬里
2) galvanized iron pipe with polyvinyl chloride lining
塑料衬里镀锌铁管;内搪胶镀锌铁管
3) Lining
[英]['laɪnɪŋ] [美]['laɪnɪŋ]
衬里
1.
Analysis of Causes Leading to Destruction of PTFE lining in Coarse Fractionating Tower;
粗馏塔聚四氟乙烯衬里的破坏分析
2.
Research & Practice of Rebound Method to Test Insulation/Wear-resisting Lining Strength;
回弹法检测隔热耐磨衬里强度的探索与实践
3.
Study of Application of Rubber Lining on Ball Mill in Lowering Noise;
球磨机橡胶衬里的设计及在降低噪声中的应用
4) liner
[英]['laɪnə(r)] [美]['laɪnɚ]
衬里
1.
Development and application of anticorrosive technique of room temperature self-vulcanization butyl rubber liner;
室温自硫化丁基橡胶衬里防腐蚀技术的开发与应用
2.
Application of epoxy resin glass fiber reinforced plastics in corrosion protection of urea prilling tower liner
环氧树脂玻璃钢衬里在尿素造粒塔防腐蚀中的应用
3.
Concerning standards for the design, manufacturing and use of PTFE liner device are introduced, application scope, total management of the liner pressure vessels and economic rationality in the manufacturing course are explored to put forward the standard of the liner device and technical specifications.
介绍了聚四氟乙烯衬里设备设计、制造和使用的相关标准,对标准的应用范围、衬里压力容器的全过程管理以及设计、制造过程中的经济合理性问题进行了探讨,提出了衬里设备标准和技术规范的改进建议。
5) liner
[英]['laɪnə(r)] [美]['laɪnɚ]
里衬
1.
While 1# unit in major repair of Longyangxia hydropower plant,the draft tube s liner and air supply short tube is destroyed seriously under high water pressure.
龙羊峡水电厂1号机大修时,检查过流部件发现尾水管里衬与补气短管在高水头下运行造成严重破坏。
2.
A great deal of fearful cracks were found in the liner steel plate of discharge ring unit four as it running off designed operating condition for long term, and these cracks have been repaired and returned to normal condition by GMAW method.
单机容量世界最大的我国福建水口电站轴流转桨式水轮发电机组 ,其中 4#机组由于长期偏离原设计工况运行 ,致使其转轮室钢板里衬产生严重裂纹。
6) lining
[英]['laɪnɪŋ] [美]['laɪnɪŋ]
衬里，衬垫
补充资料：塑料衬里
分子式：
CAS号：
性质：用塑料薄膜、塑料板材或塑料内管覆盖金属设备或管道的内表面称为塑料衬里。塑料衬里的设备主要用于介质对金属有腐蚀作用的场合。所用塑料的品种，视介质和使用条件而定。常用作衬里的塑料有：聚氯乙烯、聚乙烯、聚丙烯、氯化聚醚等。塑料可借热压法或粘接法衬在设备内表面上；也可做成塑料衬套，放在金属设备中。但一般塑料的使用温度不宜太高，导热性能不好，故塑料衬里设备一般不宜用于温度较高及需要传热的场合。
CAS号：
性质：用塑料薄膜、塑料板材或塑料内管覆盖金属设备或管道的内表面称为塑料衬里。塑料衬里的设备主要用于介质对金属有腐蚀作用的场合。所用塑料的品种，视介质和使用条件而定。常用作衬里的塑料有：聚氯乙烯、聚乙烯、聚丙烯、氯化聚醚等。塑料可借热压法或粘接法衬在设备内表面上；也可做成塑料衬套，放在金属设备中。但一般塑料的使用温度不宜太高，导热性能不好，故塑料衬里设备一般不宜用于温度较高及需要传热的场合。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条